Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER S PACEMAN, AUTOMATIC TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1271 (MANUAL TRANSMISSION - REPAIR INSTRUCTIONS)
2013 Mini Cooper S Paceman, Automatic Trans
Section 1271 (Manual Transmission - Repair Instructions)
2013 Mini Cooper S Paceman, Automatic TransSECTION Section 1271 (Manual Transmission - Repair Instructions)
WARNING: This page is about a different car, the 2010 BMW M5, 2009 BMW M5, 2008 BMW M5, 2007 BMW M5, and 2006 BMW M5. However, it is still accessible from the selected car via links, so may be relevant.
- Complete Transmission
- 00 Danger of poisoning if oil is ingested/absorbed through the skin
- 00 Risk of injury if oil comes into contact with eyes and skin
- 00 Safety instructions for handling oil
- 23 Transmission designations
- 00 11..... Draining/topping up gear oil in manual transmission
- 00 11 230 Changing/supplementing/checking transmission oil in manual transmission (GS7S47BG SMG)
- 23... Universal BMW transmission take-up
- 23..... Universal transmission retaining bridge
- 23 00... Overview of transmission housing (GS6-53BZ)
- 23 00... Overview of transmission housing (GS7S47BG SMG)
- 23 00... Replacing speed sensor (transmission main shaft) (GS6S53BZ)
- 23 00 018 Removing and installing transmission (GS6-53BZ)
- 23 00 037 Installing replacement transmission (GS6-53BZ)
- 23 00 123 Installing replacement transmission (GS7S47BG SMG)
- 23 00 613 Removing and installing transmission (GS7S47BG SMG)
- Housing With Cover
- Bearing In Housing
- 23 12 057 Replacing radial shaft seal for output flange (GS7S47BG SMG)
- 23 12 059 Replacing radial shaft seal for output shaft (GS6-53BZ/DZ)
- 23 12 089 Replacing radial shaft seal for selector shaft (GS6-53BZ/DZ)
- 23 12 510 Replacing radial shaft seal for drive shaft (GS6-53BZ)
- 23 12 512 Replacing radial shaft seal for drive shaft (GS7S47BG SMG)
- Electrical Add-On Parts
- Hydraulic Attachments
- 21 54 507 Replacing clutch position sensor (GS7S47BG SMG)
- 23 42... Bleeding procedure after replacing electric motor (GS7S47BG SMG)
- 23 42... Removing hydraulic pump relay (GS7S47BG SMG)
- 23 42... Sealing hydraulic unit and actuator block (GS7S47BG SMG)
- 23 42 020 Replacing electric motor on hydraulic pump (GS7S47BG SMG)
- 23 42 506 Replacing SMG control unit (GS7S47BG SMG)
- 23 42 519 Replacing pressure accumulator (GS7S47BG SMG)
- 23 42 534 Replacing complete hydraulic unit (GS7S47BG SMG)
- 23 42 562 Replacing clutch actuator (GS7S47BG SMG)
- 23 42 580 Replacing pressure sensor (GS7S47BG SMG)
- 23 42 581 Replacing temperature sensor (GS7S47BG SMG)
- 23 42 604 Replace all switch valves (GS7S47BG SMG)
- 23 42 620 Replacing clutch valve (GS7S47BG SMG)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.