Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMINI2013COOPER JCW, 2D CONVERTIBLE, STANDARD TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2315 (ENGINE - REPAIR (N52K))
2013 Mini Cooper JCW, 2D Convertible, Standard Trans
Section 2315 (Engine - Repair (N52K))
2013 Mini Cooper JCW, 2D Convertible, Standard TransSECTION Section 2315 (Engine - Repair (N52K))
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2013 BMW 128i, 2012 BMW 128i, 2011 BMW 128i, 2010 BMW 128i, and 2009 BMW 128i. However, it is still accessible from the selected car via links, so may be relevant.
- Engine General
- 00 Danger Of Poisoning If Oil Is Ingested/Absorbed Through The Skin
- 00 Risk Of Injury If Oil Comes Into Contact With Eyes And Skin
- 00 Safety Instructions For Handling Oil
- 11 00 Removing And Installing/Replacing Acoustic Cover (N52/N52K)
- 11 00... Engine Oil Service (N52K)
- 11 00 050 Removing And Installing Engine (N52K)
- 11 00 670 Securing Engine In Installation Position (N52)
- Engine Identification
- Mounting Engine On Assembly Stand (N52K)
- 00 Safety Information For Working On Vehicles With Automatic Engine Start-Stop Function (MSA)
- Cylinder Head And Cylinder Head Cover
- Oil Sump
- Housing Cover
- Crankshaft With Bearing
- Flywheel
- Vibration Damper
- Connecting Rod With Bearing
- Piston With Rings And Pin
- V-Ribbed Belt With TENSIONER Deflection Element
- Camshaft
- 11 31 005 Checking Timing Of Camshaft(s) (N52K)
- 11 31 025 Removing And Installing/Replacing Inlet Camshaft (N52K)
- 11 31 028 Removing And Installing/Replacing Exhaust Camshaft (N52K)
- 11 31 051 Replacing Timing Chain (N52K)
- 11 31 090 Installing And Removing/Replacing Chain Tensioner Piston (N52K)
- 11 31 505 Adjusting Timing Of Camshaft(s) (N52K)
- Rocker Arm With Bearing Mount
- Valves With Springs
- Variable Camshaft Timing
- Variable Valve Gear
- Oil Supply
- Oil Pump With Filter And Drive
- Oil Filter And Lines
- Water Pump With Drive
- Thermostat And Connections
- Intake Manifold
- Exhaust Manifold
- 18 40 050 Removing And Installing/Replacing Front Exhaust Manifold (N52, N52K)
- 18 40 050 Removing And Installing/Replacing Front Exhaust Manifold (N53/N52/N52K/N51)
- 18 40 060 Removing And Installing/Replacing Rear Exhaust Manifold (N52, N52K)
- 18 40 060 Removing And Installing/Replacing Rear Exhaust Manifold (N53/N52/N52K/N51)
- Vacuum Pump
- Emission Control, Oxygen Sensor
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.