Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2010MARINER HYBRID, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 266 (AUTOMATIC TRANSMISSION)SPECIFICATIONSTORQUE SPECIFICATION
2010 Mercury Mariner Hybrid, AWD
Torque Specification
2010 Mercury Mariner Hybrid, AWDSECTION Torque Specification
WARNING: This page is about a different car, the 2006 Mercury Grand Marquis and 2006 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATION
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Rear transmission support crossmember bolts | 55 | 41 | - |
| Transmission mount nuts | 30 | 22 | - |
| Rear insulator bolts | 90 | 66 | - |
| Extension housing bolts | 28 | 21 | - |
| Transmission fluid pan bolts | 14 | 10 | - |
| Front pump bolts | 27 | 20 | - |
| Front pump support bolts | 23 | 17 | - |
| Inspection cover bolts | 35 | 26 | - |
| Main control valve body bolts | 10 | - | 89 |
| Main control valve body cover plate bolts | 10 | - | 89 |
| Main control valve body separator plate bolts | 10 | - | 89 |
| Main control valve body reinforcement plates | 10 | - | 89 |
| Manual lever shaft nut | 33 | 24 | - |
| Manual lever shaft outer nut | 33 | 24 | - |
| Fluid cooler line case fittings | 21 | 15 | - |
| Pressure tap plugs | 12 | 9 | - |
| Rear driveshaft bolts | 112 | 83 | - |
| Starter bolts | 25 | 18 | - |
| TCC solenoid bolt | 10 | - | 89 |
| Torque converter drain plug | 12 | 9 | - |
| Torque converter nuts | 36 | 27 | - |
| Digital transmission range (TR) sensor bolts | 10 | - | 89 |
| Transmission case bolts | 47 | 35 | - |
| Output shaft speed (OSS) sensor bolt | 12 | 9 | - |
| Turbine shaft speed (TSS) sensor bolt | 11 | 8 | - |
| Starter B+ cable | 12 | 9 | - |
| Exhaust flange nuts | 48 | 35 | - |
| Exhaust flange bolts | 40 | 30 | - |
| Transmission vent tube | 12 | 9 | - |
| Manual control valve detent lever spring bolt | 10 | - | 89 |
| Cooler tube nut to case fitting | 18 | 13 | - |
| Transmission linkage | 30 | 22 | - |
| Shift cable bracket | 14 | 10 | - |
| Starter solenoid nut (small) | 6 | - | 53 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.