Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2010MARINER HYBRID, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1414 (FRONT SUSPENSION)SPECIFICATIONS
2010 Mercury Mariner Hybrid, AWD
Section 1414 (Front Suspension): Specifications
2010 Mercury Mariner Hybrid, AWDSECTION Specifications
WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
MATERIAL
| Item | Specification | Fill Capacity |
|---|---|---|
| Silicone Brake Caliper Grease and Dielectric Compound XG-3-A |
ESE-M1C171-A | - |
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in | ||
|---|---|---|---|---|---|
| Brake caliper anchor plate bolt | 90 | 66 | - | ||
| Brake disc bolt | 20 | - | 177 | ||
| Brake flexible hose bracket-to-wheel knuckle bolt | 20 | - | 177 | ||
| Catalytic converter nuts | 40 | 30 | - | ||
| Damper fork-to-front lower arm bolt | 103 | 76 | - | ||
| Front lower arm-to-subframe bolt (1) | - | - | - | ||
| Lower ball joint nut | 200 | 148 | - | ||
| Rear driveshaft-to-Power Transfer Unit (PTU) bolts | 70 | 52 | - | ||
| Rear lower arm-to-subframe bolt (1) | - | - | - | ||
| Shock absorber rod nut | 40 | 30 | - | ||
| Shock absorber-to-damper fork bolt | 48 | 35 | - | ||
| Shock absorber upper mount nut | 30 | 22 | - | ||
| Stabilizer bar bracket nut | 48 | 35 | - | ||
| Stabilizer bar link nuts | 42 | 31 | - | ||
| Steering column shaft bolt (vehicles with Hydraulic Power Assist Steering (HPAS)) | 25 | 18 | - | ||
| Steering column shaft bolt (vehicles with Electronic Power Assist Steering (EPAS)) | 20 | - | 177 | ||
| Steering gear-to-subframe bolt | 107 | 79 | - | ||
| Subframe bracket-to-body bolt | 103 | 76 | - | ||
| Subframe bracket-to-subframe nut | 150 | 111 | - | ||
| Tie-rod end nut | 48 | 35 | - | ||
| Underbody cover shield bolts | 7 | - | 62 | ||
| Upper arm-to-body bolt | 55 | 41 | - | ||
| Upper ball joint nut | 48 | 35 | - | ||
| Wheel hub nut | 255 | 189 | - | ||
| Wheel speed sensor bolt | 23 | 17 | - | ||
| Wheel speed sensor harness bolt | 23 | 17 | - | ||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.