Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2009MILAN PREMIER, 3.0 1, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 250 (ANTI-LOCK BRAKE SYSTEM)DIAGNOSIS AND TESTINGANTI-LOCK CONTROLANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX
2009 Mercury Milan Premier, 3.0 1, AWD
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index
2009 Mercury Milan Premier, 3.0 1, AWDSECTION Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index
WARNING: This page is about a different car, the 2006 Mercury Grand Marquis and 2006 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.
ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX
| DTCs | DTC Caused By | Description | Action |
|---|---|---|---|
| B1342 | ABS Module | ECU is Defective | INSTALL a new ABS module. REFER to ANTI-LOCK BRAKE SYSTEM (ABS) MODULE . |
| B1484 | ABS Module | Brake Pedal Input Open Circuit | GO to PINPOINT TEST D . |
| B1596 | ABS Module | Service Continuous Codes |
NOTE:
If other DTCs are present, REPAIR them before installing a new component. TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the ANTI-LOCK BRAKE SYSTEM (ABS) MODULE DIAGNOSTIC CODE (DTC) INDEX . If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the SYMPTOM CHART . |
| B1676 | ABS Module | Battery Voltage Out of Range | GO to PINPOINT TEST E . |
| C1145 | ABS Module | Speed Wheel Sensor RF Input Circuit Failure | GO to PINPOINT TEST B . |
| C1155 | ABS Module | Speed Wheel Sensor LF Input Circuit Failure | GO to PINPOINT TEST B . |
| C1165 | ABS Module | Speed Wheel Sensor RR Input Circuit Failure | GO to PINPOINT TEST B . |
| C1175 | ABS Module | Speed Wheel Sensor LR Input Circuit Failure | GO to PINPOINT TEST B . |
| C1222 | ABS Module | Speed Wheel Mismatch | Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. |
| C1266 | ABS Module | ABS Valve Power Relay Circuit Failure | GO to PINPOINT TEST K . |
| C1296 | ABS Module | Wheel Speed LF Signal Fault | GO to PINPOINT TEST C . |
| C1297 | ABS Module | Wheel Speed RF Signal Fault | GO to PINPOINT TEST C . |
| C1298 | ABS Module | Wheel Speed RR Signal Fault | GO to PINPOINT TEST C . |
| C1299 | ABS Module | Wheel Speed LR Signal Fault | GO to PINPOINT TEST C . |
| C1300 | ABS Module | ABS Hydraulic Pump Motor Circuit Failure | GO to PINPOINT TEST A . |
| C1805 | ABS Module | Mismatched PCM and ABS Modules Do Not Match | CHECK the part numbers. INSTALL the correct module. |
| C2775 | ABS Module | TC ON/OFF Switch Stuck Failure | GO to PINPOINT TEST H . |
| U0073 | CAN Bus | Control Module Communication Bus Off | REFER to MODULE COMMUNICATIONS NETWORK . |
| U1900 | CAN Bus | CAN communication Bus Fault - Receive error | REFER to MODULE COMMUNICATIONS NETWORK . |
| U2023 | CAN Bus | Fault received from External Node | REFER to MODULE COMMUNICATIONS NETWORK . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.