Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2009MILAN PREMIER, 3.0 1, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1821 (INFORMATION SYSTEM AND ENTERTAINMENT SYSTEM)DIAGNOSIS AND TESTINGINFORMATION AND ENTERTAINMENT SYSTEMDTC CHARTS
2009 Mercury Milan Premier, 3.0 1, AWD
DTC Charts
2009 Mercury Milan Premier, 3.0 1, AWDSECTION DTC Charts
WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
AUDIO CONTROL MODULE (ACM) DTC CHART - FUSION, MILAN WITHOUT NAVIGATION
| DTC | Description | Action |
|---|---|---|
| B1031 | SDARS Satellite Antenna Open | GO to PINPOINT TEST B . |
| B1032 | SDARS Satellite Antenna Short | GO to PINPOINT TEST B . |
| B1117 | Audio Steering Wheel Button Stuck | GO to PINPOINT TEST Q . |
| B1318 | Battery Voltage Low | GO to PINPOINT TEST AO . |
| B1342 | ECU is Faulted |
NOTE:
DTC B1342 may set as a result of a speaker circuit fault. In this case, DTC B2965 should also be set. Be sure to repair the speaker circuit fault before diagnosing DTC B1342. CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is the only DTC retrieved again, INSTALL a new Audio Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) - FUSION, MILAN or AUDIO CONTROL MODULE (ACM) - MKZ in this service information. TEST the system for normal operation. |
| B2103 | Antenna Not Connected | GO to PINPOINT TEST A . |
| B2404 | Audio Steering Wheel Switch Circuit Fault | GO to PINPOINT TEST Q . |
| B2406 | Audio Disc CD Player Internal Fault |
NOTE:
DTC B1342 may also be set. CLEAR the DTCs. REPEAT the self-test. If DTC B2406 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) - FUSION, MILAN or AUDIO CONTROL MODULE (ACM) - MKZ in this service information. TEST the system for normal operation. |
| B2477 | Module Configuration Failure | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| B2965 | Audio System Speaker Circuit Fault | For the base or mid-level audio system, GO to PINPOINT TEST C . For Sony® sound, GO to PINPOINT TEST E . |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to PINPOINT TEST AE . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | GO to PINPOINT TEST AG . |
| U0159 | Lost Communication With Parking Assist Control Module (PAM) | GO to PINPOINT TEST U . |
| U0197 | Lost Communication With Telephone Control Module | GO to PINPOINT TEST AK . |
| U0238 | Lost Communication With Digital Audio Control Module "D" (DSP) | GO to PINPOINT TEST AL . |
| U0255 | Lost Communication With Front Controls Interface Module | GO to PINPOINT TEST AM . |
| U0256 | Lost Communication With Front Display Interface Module | GO to PINPOINT TEST AN . |
| U2050 | No Application Present | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2051 | One or More Calibration Files Missing/Corrupt | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
AUDIO CONTROL MODULE (ACM) DTC CHART - MKZ WITHOUT NAVIGATION
| DTC | Description | Action |
|---|---|---|
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage out of Range | GO to PINPOINT TEST Q . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST Q . |
| B1A01:01 | Speaker #1: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A01:11 | Speaker #1: Circuit Short to Ground | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A01:13 | Speaker #1: Circuit Open | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A02:01 | Speaker #2: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A02:13 | Speaker #2: Circuit Open | For premium sound, GO to PINPOINT TEST D . For THX® sound, GO to PINPOINT TEST F . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST D . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST D . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST D . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST D . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST D . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST D . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST D . |
| B1A05:02 | Speaker #5: General Signal Failure | GO to PINPOINT TEST D . |
| B1A06:02 | Speaker #6: General Signal Failure | GO to PINPOINT TEST D . |
| B1A56:21 | Antenna: Signal Amplitude □ Minimum | GO to PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST B . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new Audio Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) - MKZ in this service information. REPEAT the self-test. |
| B1D78:13 | Auxiliary Input: Circuit Open | GO to PINPOINT TEST R . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to PINPOINT TEST U . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AK . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to PINPOINT TEST AL . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AN . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AM . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) - MKZ in this service information. REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) - MKZ in this service information. REPEAT the self-test. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST I . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AO . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AP . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
AUDIO CONTROL MODULE (ACM) DTC CHART - NAVIGATION
| DTC | Description | Action |
|---|---|---|
| B119F:01 | GPS Antenna: General Electrical Failure | GO to PINPOINT TEST W . |
| B119F:13 | GPS Antenna: Circuit Open | GO to PINPOINT TEST W . |
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage out of Range | GO to PINPOINT TEST Q . |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST Q . |
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage out of Range | GO to PINPOINT TEST Q . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST Q . |
| B121C:01 | Hard Drive: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B121C:01 is retrieved again, INSTALL a new Audio Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) - FUSION, MILAN or AUDIO CONTROL MODULE (ACM) - MKZ in this service information. REPEAT the self-test. |
| B1A01:01 | Speaker #1: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For Sony® sound, GO to PINPOINT TEST E . For THX® sound, GO to PINPOINT TEST F . |
| B1A02:01 | Speaker #2: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For Sony® sound, GO to PINPOINT TEST E . For THX® sound, GO to PINPOINT TEST F . |
| B1A03:01 | Speaker #3: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For Sony® sound, GO to PINPOINT TEST E . For THX® sound, GO to PINPOINT TEST F . |
| B1A04:01 | Speaker #4: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For Sony® sound, GO to PINPOINT TEST E . For THX® sound, GO to PINPOINT TEST F . |
| B1A05:01 | Speaker #5: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For Sony® sound, GO to PINPOINT TEST E . For THX® sound, GO to PINPOINT TEST F . |
| B1A06:01 | Speaker #6: General Electrical Failure | For premium sound, GO to PINPOINT TEST D . For Sony® sound, GO to PINPOINT TEST E . For THX® sound, GO to PINPOINT TEST F . |
| B1A07:01 | Speaker #7: General Electrical Failure | GO to PINPOINT TEST Y . |
| B1A56:21 | Antenna: Signal Amplitude □ Minimum | GO to PINPOINT TEST A . |
| B1A89:01 | Satellite Antenna: General Electrical Failure | GO to PINPOINT TEST B . |
| B1A89:13 | Satellite Antenna: Circuit Open | GO to PINPOINT TEST B . |
| B1D19:49 | Compact Disc Unit: Internal Electronic Failure | CLEAR the DTCs. REPEAT the self-test. If DTC B1D19:49 is retrieved again, INSTALL a new Audio Control Module (ACM). REFER to AUDIO CONTROL MODULE (ACM) - FUSION, MILAN or AUDIO CONTROL MODULE (ACM) - MKZ in this service information. REPEAT the self-test. |
| B1D19:4B | Compact Disc Unit: Over Temperature | The ACM was over-temperature. This may occur during extended use. Audio operation can resume after the ACM cools. CLEAR the DTCs. This is normal operation. |
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST V . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to PINPOINT TEST U . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to PINPOINT TEST M . |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to PINPOINT TEST AH . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AK . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to PINPOINT TEST AL . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AM . |
| U2014:09 | Control Module Hardware: Component Failure | GO to PINPOINT TEST X . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new ACM. REFER to AUDIO CONTROL MODULE (ACM) - FUSION, MILAN or AUDIO CONTROL MODULE (ACM) - MKZ in this service information. REPEAT the self-test. |
| U2014:96 | Control Module Hardware: Component Internal Failure | GO to PINPOINT TEST I . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AO . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AP . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE DTC CHART - SONY® SOUND
| DTC | Description | Action |
|---|---|---|
| B1A01:01 | Speaker #1: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A01:11 | Speaker #1: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST E . |
| B1A02:01 | Speaker #2: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST E . |
| B1A03:01 | Speaker #3: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST E . |
| B1A04:01 | Speaker #4: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST E . |
| B1A05:01 | Speaker #5: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A05:11 | Speaker #5: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A05:12 | Speaker #5: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A05:13 | Speaker #5: Circuit Open | GO to PINPOINT TEST E . |
| B1A06:01 | Speaker #6: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A06:11 | Speaker #6: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A06:12 | Speaker #6: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A06:13 | Speaker #6: Circuit Open | GO to PINPOINT TEST E . |
| B1A07:01 | Speaker #7: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A07:11 | Speaker #7: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A07:12 | Speaker #7: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A07:13 | Speaker #7: Circuit Open | GO to PINPOINT TEST E . |
| B1A08:01 | Speaker #8: General Electrical Failure | GO to PINPOINT TEST E . |
| B1A08:11 | Speaker #8: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A08:12 | Speaker #8: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A08:13 | Speaker #8: Circuit Open | GO to PINPOINT TEST E . |
| B1A09:02 | Speaker #9: General Signal Failure | GO to PINPOINT TEST E . |
| B1A09:12 | Speaker #9: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A09:13 | Speaker #9: Circuit Open | GO to PINPOINT TEST E . |
| B1A10:11 | Speaker #10: Circuit Short to Ground | GO to PINPOINT TEST E . |
| B1A10:12 | Speaker #10: Circuit Short to Battery | GO to PINPOINT TEST E . |
| B1A10:13 | Speaker #10: Circuit Open | GO to PINPOINT TEST E . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AJ . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AK . |
| U2014:01 | Control Module Hardware: General Electrical Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:01 is retrieved again, INSTALL a new audio Digital Signal Processing (DSP) module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE in this service information. REPEAT the self-test. |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new audio Digital Signal Processing (DSP) module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE in this service information. REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AS . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AT . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE DTC CHART - THX® SOUND
| DTC | Description | Action |
|---|---|---|
| B1A01:11 | Speaker #1: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A01:12 | Speaker #1: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A01:13 | Speaker #1: Circuit Open | GO to PINPOINT TEST F . |
| B1A02:11 | Speaker #2: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A02:12 | Speaker #2: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A02:13 | Speaker #2: Circuit Open | GO to PINPOINT TEST F . |
| B1A03:11 | Speaker #3: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A03:12 | Speaker #3: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A03:13 | Speaker #3: Circuit Open | GO to PINPOINT TEST F . |
| B1A04:11 | Speaker #4: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A04:12 | Speaker #4: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A04:13 | Speaker #4: Circuit Open | GO to PINPOINT TEST F . |
| B1A05:11 | Speaker #5: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A05:12 | Speaker #5: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A05:13 | Speaker #5: Circuit Open | GO to PINPOINT TEST F . |
| B1A06:11 | Speaker #6: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A06:12 | Speaker #6: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A06:13 | Speaker #6: Circuit Open | GO to PINPOINT TEST F . |
| B1A07:11 | Speaker #7: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A07:12 | Speaker #7: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A07:13 | Speaker #7: Circuit Open | GO to PINPOINT TEST F . |
| B1A08:11 | Speaker #8: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A08:12 | Speaker #8: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A08:13 | Speaker #8: Circuit Open | GO to PINPOINT TEST F . |
| B1A09:11 | Speaker #9: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A09:12 | Speaker #9: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A09:13 | Speaker #9: Circuit Open | GO to PINPOINT TEST F . |
| B1A10:11 | Speaker #10: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A10:12 | Speaker #10: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A10:13 | Speaker #10: Circuit Open | GO to PINPOINT TEST F . |
| B1A11:11 | Speaker #11: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A11:12 | Speaker #11: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A11:13 | Speaker #11: Circuit Open | GO to PINPOINT TEST F . |
| B1A12:11 | Speaker #12: Circuit Short to Ground | GO to PINPOINT TEST F . |
| B1A12:12 | Speaker #12: Circuit Short to Battery | GO to PINPOINT TEST F . |
| B1A12:13 | Speaker #12: Circuit Open | GO to PINPOINT TEST F . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AJ . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AK . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is retrieved again, INSTALL a new audio Digital Signal Processing (DSP) module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE in this service information. REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is retrieved again, INSTALL a new audio DSP module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE in this service information. REPEAT the self-test. |
| U2014:4B | Control Module Hardware: Over Temperature | The audio DSP module was over-temperature. This may occur during extended use. Audio operation can resume after the audio DSP module cools. CLEAR the DTCs. This is normal operation. |
| U2014:96 | Control Module Hardware: Component Internal Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:96 is retrieved again, INSTALL a new audio DSP module. REFER to AUDIO DIGITAL SIGNAL PROCESSING (DSP) MODULE in this service information. REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AS . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AT . |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
ACCESSORY PROTOCOL INTERFACE MODULE (APIM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| B1201:1C | Steering Wheel Audio Switch Pack 2: Circuit Voltage Out of Range | GO to PINPOINT TEST Q . |
| B1201:63 | Steering Wheel Audio Switch Pack 2: Circuit/Component Protection Time-Out | GO to PINPOINT TEST Q . |
| B1252:04 | USB Port: System Internal Failure | GO to PINPOINT TEST AB . |
| B1252:11 | USB Port: Circuit Short to Ground | GO to PINPOINT TEST AB . |
| B1A16:01 | Microphone Input Circuit: General Electrical Failure | GO to PINPOINT TEST V . |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to PINPOINT TEST AD . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to PINPOINT TEST AF . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to PINPOINT TEST AI . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AJ . |
| U0255:00 | Lost Communication With Front Display Interface Module: No Sub Type Information | GO to PINPOINT TEST AN . |
| U0256:00 | Lost Communication With Front Controls Interface Module: No Sub Type Information | GO to PINPOINT TEST AM . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the Accessory Protocol Interface Module (APIM) or Smart Junction Box (SJB). |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Instrument Panel Cluster (IPC). |
| U046B:00 | Invalid Data Received From Global Positioning System Module: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Global Positioning System Module (GPSM). |
| U0485:00 | Invalid Data Received From Radio: No Sub Type Information | RETRIEVE and FOLLOW other DTCs present in the APIM or Audio Control Module (ACM). |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2101:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST Z . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) in this service information. REPEAT the self-test. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new APIM. REFER to ACCESSORY PROTOCOL INTERFACE MODULE (APIM) . REPEAT the self-test. |
| U3000:88 | Control Module: Bus Off | REFER to MODULE COMMUNICATIONS NETWORK -- FUSION, MILAN & MKZ article. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AQ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AR . |
FRONT CONTROLS INTERFACE MODULE (FCIM) DTC CHART - FUSION, MILAN WITHOUT NAVIGATION
| DTC | Description | Action |
|---|---|---|
| B1318 | Battery Voltage Low | GO to PINPOINT TEST AU . |
| B1342 | ECU is Faulted | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is still present, INSTALL a new Front Controls Interface Module (FCIM). REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) - FUSION, MILAN in this service information. REPEAT the self-test. |
| B2924 | Audio Button Stuck | GO to PINPOINT TEST J . |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to PINPOINT TEST AE . |
| U0164 | Lost Communication With HVAC Control Module (EATC) | GO to PINPOINT TEST AH . |
| U0184 | Lost Communication With Radio (ACM) | GO to PINPOINT TEST AJ . |
| U2050 | No Application Present | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2051 | One or More Calibration Files Missing/Corrupt | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
FRONT CONTROLS INTERFACE MODULE (FCIM) DTC CHART - MKZ WITHOUT NAVIGATION, ALL VEHICLES WITH NAVIGATION
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AJ . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST J . |
| U2014:41 | Control Module Hardware: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:41 is still present, INSTALL a new Front Controls Interface Module (FCIM). REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) - MKZ in this service information. REPEAT the self-test. |
| U2014:42 | Control Module Hardware: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2014:42 is still present, INSTALL a new FCIM. REFER to FRONT CONTROLS INTERFACE MODULE (FCIM) - MKZ in this service information. REPEAT the self-test. |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AU . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AV . |
FRONT DISPLAY INTERFACE MODULE (FDIM) DTC CHART - VEHICLES WITHOUT NAVIGATION
| DTC | Description | Action |
|---|---|---|
| B1318 | Battery Voltage Low | GO to PINPOINT TEST AW . |
| B1342 | ECU is Faulted | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is still present, INSTALL a new Front Display Interface Module (FDIM). REFER to FRONT DISPLAY INTERFACE MODULE (FDIM) - FUSION, MILAN or FRONT DISPLAY INTERFACE MODULE (FDIM) - MKZ in this service information. REPEAT the self-test. |
| B2477 | Module Configuration Failure | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| B2924 | Audio Button Stuck | GO to PINPOINT TEST AZ . |
| U0140 | Lost Communication With Body Control Module (GEM) | GO to PINPOINT TEST AE . |
| U0155 | Lost Communication With Instrument Panel Cluster (IC) Control Module | GO to PINPOINT TEST AG . |
| U0164 | Lost Communication With HVAC Control Module (EATC) | GO to PINPOINT TEST AH . |
| U0184 | Lost Communication With Radio (ACM) | GO to PINPOINT TEST AJ . |
| U0197 | Lost Communication With Telephone Control Module | GO to PINPOINT TEST AK . |
| U0238 | Lost Communication With Digital Audio Control Module "D" (DSP) | GO to PINPOINT TEST AL . |
| U2050 | No Application Present | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
| U2051 | One or More Calibration Files Missing/Corrupt | REFER to MODULE CONFIGURATION -- FUSION MILAN & MKZ article. |
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure-type code. The failure-type code provides information about specific fault conditions such as opens, or shorts to ground. Continuous memory DTCs have an additional 2-character DTC status code suffix to assist in determining DTC history.
GLOBAL POSITIONING SYSTEM MODULE (GPSM) DTC CHART
| DTC | Description | Action |
|---|---|---|
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST AG . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AJ . |
| U0197:00 | Lost Communication With Telephone Control Module: No Sub Type Information | GO to PINPOINT TEST AK . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW diagnostics for other DTCs present in the Global Positioning System Module (GPSM) and Restraints Control Module (RCM). |
| U0423:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW diagnostics for other DTCs present in the GPSM and Instrument Panel Cluster (IPC). |
| U3000:09 | Control Module: Component Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:09 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) - FUSION, MILAN or GLOBAL POSITIONING SYSTEM MODULE (GPSM) - MKZ in this service information. REPEAT the self-test. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) - FUSION, MILAN or GLOBAL POSITIONING SYSTEM MODULE (GPSM) - MKZ in this service information. REPEAT the self-test. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, INSTALL a new GPSM. REFER to GLOBAL POSITIONING SYSTEM MODULE (GPSM) - FUSION, MILAN or GLOBAL POSITIONING SYSTEM MODULE (GPSM) - MKZ in this service information. REPEAT the self-test. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AX . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AY . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.