SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2009MILAN PREMIER, 3.0 1, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1764 (ENGINE CONTROLS - REFERENCE VALUES (EXCEPT DIESEL & HYBRID))TYPICAL DIAGNOSTIC REFERENCE VALUES3.0L 4V FUSION/MILAN
2009 Mercury Milan Premier, 3.0 1, AWD

3.0L 4V Fusion/Milan

2009 Mercury Milan Premier, 3.0 1, AWDSECTION 3.0L 4V Fusion/Milan
WARNING: This page does not describe the selected car, but rather 29 other vehicles, including the 2011 Mercury Milan, 2011 Mercury Mariner, 2011 Lincoln Navigator L, 2011 Lincoln Navigator, and 2011 Lincoln MKZ. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: 190 Pin PCM Connectors - 3.0L 4V Fusion/Milan
G06054072Courtesy of FORD MOTOR CO.

Typical Diagnostic Reference Values 

SENSORS - 3.0L 4V FUSION/MILAN

Sensors/Inputs PCM Pin/PID only Measured/PID Values Units Measured/PID
KOEO Hot Idle 48 KM/H (30 MPH) 89 KM/H (55 MPH)
BOO1 B13 OFF ON (E) OFF OFF ON/OFF
APP1 B28 0.76 0.76 1.05 0.76 VOLTS
APP2 B29 0.37 0.37 0.51 0.37 VOLTS
FPM B32 43.18 59.71 60.35 59.71 %
MAF B40 0 0.68 1.27 1.83 VOLTS
BOO2 B46 OFF ON (E) OFF OFF ON/OFF
IAT B47 1.75/48.8 (120) 2.02/42.7 (109) 3.16/17.7 (64) 3.22/17.2 (63) VOLTS/DEG C (DEG F)
FTP B65 2.6/-0 2.6/-0 2.57/-0.01 2.5/-0.03 VOLTS/PSI
FTP_H2O B65 -0.07 -0.69 0 -0.03 in-H2 O
O2S21_CUR E10 (I) switching switching switching mA/uA
O2S11_CUR E27 (I) switching switching switching mA/uA
CHT E39 0.54/94 (201.2) 0.6/90 (194) 3.81/88 (190.4) 3.52/97 (206.6) VOLTS/DEG C (DEG F)
MAP E40 4.02/98.93/14.35/28.93 1.28/30.95/4.49/9.15 1.35/32.95/4.78/9.73 2.33/57.98/8.41/17.12 VOLTS/kPa/PSI/inHg
TP1 E41 4.05 4.29 4.17 4 VOLTS
KNOCK_1 E43 117 112 256 447 N/A
TP2 E58 1.22 0.74 0.99 1.3 VOLTS
KNOCK_2 E60 168 178 280 409 N/A
O2S11_HTR E69 20 32.54 31.76 34.11 %
O2S21_HTR E70 20 32.54 30.98 31.76 %
O2S12 T29 (I) (D) (D) (D) VOLTS
O2S22 T40 (I) (D) (D) (D) VOLTS
HTRCM22 T48 605 605 605 605 mA
HTRCM12 T49 617 617 617 617 mA
APP PID 0 0 8.5 0 %
BARO PID 14.48/157.4 14.48/157.4 14.48/157.4 14.48/157.4 PSI/Hz
B+ PID 12.87 13-14 13-14 13-14 VOLTS
DECHOKE PID NO NO NO NO YES/NO
ETC_ACT PID 8 2.62 6.45 8.93 DEG
ETC_DSD PID 7.79 2.62 6.45 9.08 DEG
FLI PID 58.43 (H) 58.43 (H) 56.86 (H) 55.29 (H) %
LOAD PID 0(I) 25.88 29.41 54.51 %
MISFIRE PID NO NO NO NO YES/NO
MP_LRN PID YES YES YES YES YES/NO
O2_DS1_ERR PID 0 0 -0.06 0.03 VOLTS
O2_DS2_ERR PID 0 0 0.32 0.03 VOLTS
O2S11_IMPED PID 5 0.09 0.09 0.09 VOLTS
O2S21_IMPED PID 5 0.09 0.09 0.09 VOLTS
RPM PID 0 766 1203 1700 RPM
SYNC PID NO YES YES YES YES/NO
VCT1_F PID NO FAULT NO FAULT NO FAULT NO FAULT FAULT/NO FAULT
VCT2_F PID NO FAULT NO FAULT NO FAULT NO FAULT FAULT/NO FAULT
VSS PID 0 0 48 km/h (30 MPH) 89 km/h (55 MPH) km/h/MPH
ACTUATORS - 3.0L 4V FUSION/MILAN

Actuators/Outputs PCM Pin/PID only Measured/PID Values Units Measured/PID
KOEO Hot Idle 48 KM/H (30 MPH) 89 KM/H (55 MPH)
FP B19 OFF ON ON ON ON/OFF
EVAPCV B20 0/OFF 0/OFF 0/OFF 0/OFF %/ON/OFF
PCVHC E6 0 0 0 0 %
EVAPCP E32 0 39.21 0 0 %
VCTDC E67 0 0 47.62 0 %
VCTDC2 E68 0 0 49.18 0 %
HTR11 E69 OFF ON ON ON ON/OFF
HTR21 E70 OFF ON ON ON ON/OFF
HTR22 T48 OFF ON ON ON ON/OFF
HTR12 T49 OFF ON ON ON ON/OFF
EGR_EVAL PID YES YES YES YES YES/NO
EVAP020C PID NO NO NO NO YES/NO
EVAPCV PID 0/OFF 0/OFF 0/OFF 0/OFF %/ON/OFF
EVAPSOAK PID YES YES YES YES YES/NO
EVAP_EVAL PID NO NO NO NO YES/NO
FUELSYS PID OPEN LOOP CLOSED LOOP CLOSED LOOP CLOSED LOOP OPEN/CLOSED LOOP
LONGFT1 PID (I) -20 TO +20 -20 TO +20 -20 TO +20 %
LONGFT2 PID (I) -20 TO +20 -20 TO +20 -20 TO +20 %
MIL_DIS PID 0 0 0 0 Miles
O2S_EVAL PID NO NO NO YES YES/NO
O2SHTR_EVAL PID NO NO NO YES YES/NO
SHRTFT1 PID (I) -10 TO +10 -10 TO +10 -10 TO +10 %
SHRTFT2 PID (I) -10 TO +10 -10 TO +10 -10 TO +10 %
SPARKADV PID 33 15 39.5 44 DEG
VCTADV PID 0 -0.37 -14.68 -0.25 DEG
VCTADV2 PID 0 -1 -15 0 DEG
VCTADVERR PID 0 -0.68 0.81 -1.25 DEG
VCTADVERR2 PID 0 0 0.68 -1.18 DEG
OTHERS - 3.0L 4V FUSION/MILAN

Other PCM Pin/PID only Measured/PID Values Units Measured/PID
KOEO Hot Idle 48 KM/H (30 MPH) 89 KM/H (55 MPH)
VREF B52/E35 5 5 5 5 VOLTS
VPWR B67/68 12.77 13-14 13-14 13-14 VOLTS
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.