Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2009MILAN PREMIER, 3.0 1, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1301 (ANTI-LOCK BRAKE SYSTEM - VEHICLE DYNAMIC SYSTEMS)DIAGNOSTIC TESTSANTI-LOCK CONTROLDTC CHARTS
2009 Mercury Milan Premier, 3.0 1, AWD
DTC Charts
2009 Mercury Milan Premier, 3.0 1, AWDSECTION DTC Charts
WARNING: This page is about a different car, the 2009 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
ABS MODULE DTC CHART
| DTC | Description | Source | Action |
|---|---|---|---|
| B1317 | Battery Voltage High | ABS Module | Go to Pinpoint Test A . |
| B1318 | Battery Voltage Low | ABS Module | Go to Pinpoint Test A . |
| B1342 | ECU is Faulted | ABS Module |
NOTE:
If other DTCs are present, repair them before installing a new module. CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . REPEAT the self-test. |
| C1095 | ABS Hydraulic Pump Motor Circuit Failure | ABS Module | Go to Pinpoint Test B . |
| C1096 | ABS Hydraulic Pump Motor Circuit Open | ABS Module | Go to Pinpoint Test B . |
| C1115 | ABS Power Relay Output Short Circuit to Battery | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1115 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1145 | Wheel Speed Sensor RF Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1155 | Wheel Speed Sensor LF Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1165 | Wheel Speed Sensor RR Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1175 | Wheel Speed Sensor LR Input Circuit Failure | ABS Module | Go to Pinpoint Test C . |
| C1185 | ABS Power Relay Output Circuit Failure | ABS Module | CLEAR all DTCs. If DTC C1185 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1194 | ABS Outlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1194 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1198 | ABS Inlet Valve Coil LF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1198 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1210 | ABS Outlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1210 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1214 | ABS Inlet Valve Coil RF Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1214 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1222 | Wheel Speed Mismatch | ABS Module | Go to Pinpoint Test D . |
| C1233 | Wheel Speed LF Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1234 | Wheel Speed RF Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1235 | Wheel Speed RR Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1236 | Wheel Speed LR Input Signal Missing | ABS Module | Go to Pinpoint Test D . |
| C1242 | ABS Outlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1242 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1246 | ABS Outlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1246 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1250 | ABS Inlet Valve Coil LR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1250 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1254 | ABS Inlet Valve Coil RR Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1254 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1329 | ABS Outlet Valve Coil RF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1329 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1330 | ABS Outlet Valve Coil LR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1330 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1331 | ABS Outlet Valve Coil RR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1331 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1332 | ABS Outlet Valve Coil LF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1332 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1333 | ABS Inlet Valve Coil LR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1333 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1334 | ABS Inlet Valve Coil LF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1334 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1335 | ABS Inlet Valve Coil RF Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1335 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1336 | ABS Inlet Valve Coil RR Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1336 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1404 | Traction Control Valve Rear Circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1404 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1446 | Brake Switch Circuit Failure | ABS Module | Go to Pinpoint Test E . |
| C1527 | Traction Control Rear Valve Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1527 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1531 | Dynamic Stability Control LF Valve Circuit Excessive Temperature | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1531 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1730 | Reference Voltage Out of Range (+5 V) | ABS Module | If any other DTCs are present, DIAGNOSE those DTCs first. CLEAR all DTCs. DRIVE the vehicle. If the DTC is still present, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| C1958 | Dynamic Stability Control Valve LF circuit Failure | ABS Module | CLEAR all DTCs. DRIVE the vehicle. If DTC C1958 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CARRY OUT the self-test with the Pinpoint Test F: Spongy/Soft/Low Brake Pedal with No Warning Indicator not applied. |
| U0073 | Control Module Communication Bus Off | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the Hydraulic Control Unit (HCU) bus. |
| U1900 | CAN Communication Bus Fault - Receive Error | ABS Module | REFER to MODULE COMMUNICATIONS NETWORK to diagnose the HCU bus. |
| U2011 | Module Transmitted Invalid Data (Non-SCP) | ABS Module | VERIFY PCM configuration, REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . If the PCM is not correctly configured, CONFIGURE the PCM. If the PCM is correctly configured, REFER to MODULE COMMUNICATIONS NETWORK to diagnose the HCU bus. |
| U2050 | No Application Present | ABS Module | CONFIGURE the ABS module. REFER to Programmable Module Installation (PMI) in MODULE CONFIGURATION . CLEAR the DTCs. RETRIEVE the DTCs and VERIFY successful module configuration. If DTC U2050 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CLEAR the DTC. REPEAT the self-test. |
| U2051 | One or More Calibration Files Missing/Corrupt | ABS Module | CALIBRATE the ABS module, follow the directions on the scan tool. CLEAR the DTCs. CARRY OUT the ABS module self-test. RETRIEVE and RECORD any DTCs. If DTC U2051 is retrieved again, INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module . CLEAR the DTC. REPEAT the self-test. |
INSTRUMENT CLUSTER DTC CHART
| DTC | Description | Source | Action |
|---|---|---|---|
| C1093 | Traction Control Disable Switch Circuit Failure | Instrument Cluster | Go to Pinpoint Test H . |
| - | All Other Instrument Cluster DTCs | Instrument Cluster | REFER to the Master DTC Chart in MULTIFUNCTION ELECTRONIC MODULES . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.