Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCURY2009MILAN PREMIER, 3.0 1, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1033 (ENGINE - 2.3L)SPECIFICATIONSTORQUE SPECIFICATIONS
2009 Mercury Milan Premier, 3.0 1, AWD
Torque Specifications
2009 Mercury Milan Premier, 3.0 1, AWDSECTION Torque Specifications
WARNING: This page is about a different car, the 2008 Mercury Milan and 2008 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| A/C compressor mounting bolts | 25 | 18 | - |
| A/C manifold tube bolt | 25 | 18 | - |
| A/C tube bracket bolts | 10 | - | 89 |
| A/C tube connection nut | 8 | - | 71 |
| A/C tube-to-condenser nut | 8 | - | 71 |
| Accessory drive belt tensioner bolts | 25 | 18 | - |
| Accessory drive belt idler pulley bolt | 25 | 18 | - |
| Bellhousing-to-engine bolts | 48 | 35 | - |
| Bellhousing-to-engine stud bolt | 48 | 35 | - |
| Bellhousing-to-oil pan bolt | 48 | 35 | - |
| Block heater | 21 | 15 | - |
| Camshaft bearing cap boltsa | - | - | - |
| Camshaft sprocket bolt | 72 | 53 | - |
| Catalytic converter boltsa | - | - | - |
| Catalytic converter bracket bolts | 35 | 26 | - |
| Catalytic converter bracket-to-catalytic converter bolts | 20 | - | 177 |
| Catalytic converter heat shield screws | 10 | - | 89 |
| Catalytic converter-to-cylinder head studs | 17 | - | 150 |
| Clutch pressure platea | - | - | - |
| Clutch slave cylinder bolts | 22 | 16 | - |
| Clutch tube bracket bolts | 22 | 16 | - |
| Coil-on-plug bolts | 8 | - | 71 |
| Coolant outlet bolts | 10 | - | 89 |
| Coolant pump bolts | 10 | - | 89 |
| Coolant pump pulley bolts | 20 | - | 177 |
| Crankcase rear seal retainer plate boltsa | - | - | - |
| Crankcase vent oil separator bolts | 10 | - | 89 |
| Crankshaft Position (CKP) sensor boltsa | - | - | - |
| Crankshaft pulley bolta | - | - | - |
| Crankshaft rear seal retainer boltsa | - | - | - |
| Cylinder head boltsa | - | - | - |
| Cylinder Head Temperature (CHT) sensor | 12 | - | 106 |
| EGR tube | 55 | 41 | - |
| EGR valve assembly bolts | 20 | - | 177 |
| Engine front cover boltsa | - | - | - |
| Engine front cover timing hole plug (lower) | 12 | - | 106 |
| Engine front cover timing hole plug (upper) | 10 | - | 89 |
| Engine front cover-to-oil pan boltsa | 10 | - | 89 |
| Engine mount bolts | 55 | 41 | - |
| Engine mount nut | 55 | 41 | - |
| Engine mount bracket nuts | 103 | 76 | - |
| Engine mount bracket bolt | 115 | 85 | - |
| Engine Oil Pressure (EOP) switch | 15 | - | 133 |
| Engine roll-restrictor bolts | 90 | 66 | - |
| Engine timing plug bolt | 20 | - | 177 |
| Engine-to-transaxle bolts | 48 | 35 | - |
| Engine wiring harness bracket nut | 20 | - | 177 |
| Flexplate boltsa | - | - | - |
| Flywheel boltsa | - | - | - |
| Fuel rail bolts | 23 | 17 | - |
| Generator air inlet duct nuts | 6 | - | 53 |
| Generator B+ wire nut | 6 | - | 53 |
| Generator mounting bolt and stud bolts | 47 | 35 | - |
| Generator splash shield nuts | 25 | 18 | - |
| Ground wire-to-battery cable nut | 10 | - | 89 |
| Ground wire-to-body bolt | 10 | - | 89 |
| Intake manifold bolts | 18 | - | 159 |
| Intermediate steering shaft bolt | 23 | 17 | - |
| Knock Sensor (KS) | 20 | - | 177 |
| Lower ball joint nuts | 200 | 148 | - |
| Lower control arm-to-strut through bolt | 103 | 76 | - |
| Oil filter adapter bolts | 25 | 18 | - |
| Oil filter cover | 33 | 24 | - |
| Oil filter drain plug | 10 | - | 89 |
| Oil pan boltsa | - | - | - |
| Oil pan-to-bellhousing bolts | 48 | 35 | - |
| Oil pan drain plug | 28 | 21 | - |
| Oil pump drive chain tensioner shoulder bolt | 10 | - | 89 |
| Oil pump drive chain tensioner spring shoulder bolt | 10 | - | 89 |
| Oil pump screen and pickup tube assembly bolts | 10 | - | 89 |
| Oil pump sprocket bolt | 25 | 18 | - |
| Oil pump-to-engine block boltsa | - | - | - |
| Power steering pump bolts | 25 | 18 | - |
| Power Steering Pressure (PSP) tube bolt | 35 | 26 | - |
| Radio frequency interference capacitor bolt | 10 | - | 89 |
| RH halfshaft carrier bearing bracket bolt | 40 | 30 | - |
| Secondary Air Injection (AIR) pump bolts | 30 | 22 | - |
| Secondary AIR valve bracket bolts | 10 | - | 89 |
| Spark plugs | 12 | - | 106 |
| Starter motor solenoid nut | 5 | - | 44 |
| Starter motor B+ wire nut | 12 | - | 106 |
| Starter motor mounting bolts | 25 | 18 | - |
| Subframe nuts | 150 | 111 | - |
| Subframe bracket bolts | 103 | 76 | - |
| Sway bar link nuts | 40 | 30 | - |
| Thermostat housing bolts | 10 | - | 89 |
| Throttle Body (TB) bolts | 10 | - | 89 |
| Tie-rod end nuts | 48 | 35 | - |
| Timing chain guide bolts | 10 | - | 89 |
| Timing chain tensioner bolts | 10 | - | 89 |
| Torque converter-to-flywheel nuts | 35 | 26 | - |
| Transaxle ground wire bolt | 10 | - | 89 |
| Transaxle mount bolt | 90 | 66 | - |
| Valve cover boltsa | - | - | - |
| Variable Camshaft Timing (VCT) solenoid bolta | 10 | - | 89 |
| VCT system oil filter plug | 17 | - | 150 |
a Refer to procedure for specification.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.