Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMERCEDES BENZ2021GT C AMG 2D CONVERTIBLEREPAIR AND DIAGNOSISCOLLISIONGENERAL COLLISION INFORMATIONCOLLISION - SUBSTRUCTURE - 190 CHASSISSUBSTRUCTURELOWER ENGINE COMPARTMENT LINING REMOVAL AND INSTALLATION - AR61.20-P-1105RG
2021 Mercedes Benz GT C AMG 2D Convertible
Lower Engine Compartment Lining Removal And Installation - Ar61.20-P-1105RG
2021 Mercedes Benz GT C AMG 2D ConvertibleSECTION Lower Engine Compartment Lining Removal And Installation - Ar61.20-P-1105RG
Model 190 (except 190.381)
MODIFICATION NOTES
| 24.01.2024 | Bolt, mount for front engine compartment paneling | Model 190 | BA61.40-P-1001-01E |
Shown on model 190.377
Shown on model 190 with code M030 (GT R version)
Shown on model 190.377
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Notice | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Remove/install | |||
| 1 | Raise vehicle. | AR00.60-P-1000RG | |
| 2 | Tighten screws (3). | ||
| *BA61.40-P-1001-01E | |||
| 3 | Unscrew bolts (2) and remove front engine compartment lining (1). | When removing front engine compartment paneling (1). Do not crush or kink or subject electric lines to tension. This will result in damage to the electric lines and can impair their function. Aid of helper required. |
|
| *BA61.40-P-1001-01E | |||
| 4 | Release and disconnect electrical connector (12). | Model 190 (except 190.381) with code M030 (GT R version) When removing front engine compartment paneling (1). |
|
| 5 | Remove screws (5). | ||
| 6 | Unscrew bolts (9) and remove left diagonal strut (7) and/or right diagonal strut (8). | When removing center engine compartment paneling (4). |
|
| *BA61.10-P-1004-01I | |||
| 7 | Unscrew the bolts (6) and remove the center engine compartment lining (4). | When removing center engine compartment paneling (4). | |
| *BA61.40-P-1003-01E | |||
| 8 | Install in the reverse order. |
FRAME FLOOR ASSEMBLY
| Number | Designation | Model 190 | |
|---|---|---|---|
| BA61.10-P-1004-01I | Bolt, diagonal strut mount to front axle carrier/longitudinal member | Nm | 55 |
UNDERBODY PROTECTION
| Number | Designation | Model 190 | |
|---|---|---|---|
| BA61.40-P-1001-01E | Bolt, mount for front engine compartment paneling | Nm | 6 |
UNDERBODY PROTECTION
| Number | Designation | Model 190 | |
|---|---|---|---|
| BA61.40-P-1003-01E | Pan head screw/screw, attachment of center engine compartment lining | Nm | 5 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.