Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Mercedes Benz SLK250 Automatic TransFACTORY OEM SERVICE PROCEDURE
Remove/install heated O2 sensor - AR07.52-P-5303MR
ENGINE 274 in MODEL 172, 204, 207
Shown on model 204
| Risk of injury . Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | AS00.00-Z-0002-01A | |
| Remove/install | |||
| 1 | Remove upper engine cover | ||
| 2 | Disconnect electrical connection (G3/2x1) | ||
| 3 | Remove oxygen sensor (G3/2) from catalytic converter | ||
| *BA14.00-P-1005-01A | |||
| Paste, hot lubrication 1 kg, DBL 6879.20 | *BR00.45-Z-1005-06A | ||
| Figure | |||
| 4 | Lift vehicle on vehicle lift | Engine 274 in model 172, 204.0/2/3, 207 | |
| 5 | Remove lower engine compartment paneling | Engine 274 in model 172 | AR61.20-P-1105W |
| Engine 274 in model 204.0/2/3, 207 | AR61.20-P-1105EW | ||
| 6 | Disconnect electrical connection (G3/1x1) | ||
| 7 | Remove oxygen sensor (G3/1) from catalytic converter | ||
| *BA14.00-P-1002-01A | |||
| Paste, hot lubrication 1 kg, DBL 6879.20 | *BR00.45-Z-1005-06A | ||
| Figure | |||
| 8 | Install in the reverse order | ||
| 9 | Read out fault memory using the diagnostic system and clear if necessary | ||
| AD00.00-P-2000-04A | |||
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| 10 | Carry out an engine test run and check exhaust system for leaktightness |
OXYGEN SENSOR
| Number | Designation | Engine 274 | |
|---|---|---|---|
| BA14.00-P-1002-01A | Oxygen sensor at catalytic converter | Nm | 50 |
OXYGEN SENSOR
| Number | Designation | Engine 274 | |
|---|---|---|---|
| BA14.00-P-1005-01A | Oxygen sensor upstream of catalytic converter | Nm | 50 |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1005-06A | Paste, hot lubrication 1 kg, DBL 6879.20 | A 000 989 76 51 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
