Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Mercedes Benz SLK250 Automatic TransFACTORY OEM SERVICE PROCEDURE
Remove/install heated O2 sensor - AR07.52-P-5303CW
ENGINES 271 in MODEL 172, 204, 207, 212
Shown on engine 271.8
Shown on engine 271.9
| Remove/install | |||
| Risk of injury to skin and eyes caused by handling hot or glowing objects. | Wear safety gloves, protective clothing and safety glasses, if necessary. | AS00.00-Z-0002-01A | |
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | AS00.00-Z-0010-01A | |
| 1 | Raise vehicle | ||
| 2 | Remove rear section of the lower engine compartment paneling | Model 204 | |
| Model 172 | AR61.20-P-1105W | ||
| Model 207, 212 |
AR61.20-P-1105EW | ||
| Oxygen sensor downstream of catalytic converter (G3/1) | |||
| 3 | Unclip and disconnect electrical connection for oxygen sensor downstream of CAT (G3/1x1) on bracket | ||
| 4 | Remove oxygen sensor downstream of CAT (G3/1) from CAT (4) | ||
| *BA14.00-P-1001-01A | |||
| Paste | *BR00.45-Z-1005-06A | ||
| Oxygen sensor upstream of catalytic converter (G3/2) | |||
| 5 | Unclip and disconnect electrical connection for oxygen sensor upstream of CAT (G3/2x1) on bracket | ||
| 6 | Unclip electrical line for oxygen sensor upstream of CAT (G3/2) on heat shield for the right engine mount | ||
| 7 | Remove oxygen sensor upstream of CAT (G3/2) from CAT (4) |
|
|
| *BA14.00-P-1001-01A | |||
| Fig 3 | |||
| Paste | *BR00.45-Z-1005-06A | ||
| 8 | Install in the reverse order | ||
| 9 | Attach STAR DIAGNOSIS and perform default initialization of the ME-SFI [ME] control unit | After replacing the oxygen sensor upstream of CAT (G3/2) |
|
| Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. |
AS00.00-Z-0005-01A | |
| 10 | Perform engine test run while checking the exhaust system for leaks |
O2 SENSOR
| Number | Designation | Engine 271 | |
|---|---|---|---|
| BA14.00-P-1001-01A | O2 sensor on exhaust pipe/exhaust manifold | Nm | 50 |
REPAIR MATERIALS
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1005-06A | Paste, hot lubrication 1 kg, DB supply specification 6879.20 | A 000 989 76 51 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
