Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA20133 I SV, 2.0L ENG VIN G, AUTOMATIC TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 375 (ON-BOARD DIAGNOSTIC (AIR BAG SYSTEM])PID/DATA MONITOR TABLE
2013 Mazda 3 i SV, 2.0L Eng VIN G, Automatic Trans
PID/Data Monitor Table
2013 Mazda 3 i SV, 2.0L Eng VIN G, Automatic TransSECTION PID/Data Monitor Table
WARNING: This page is about a different car, the 2005 Mazda 6. However, it is still accessible from the selected car via links, so may be relevant.
PID/DATA MONITOR
| PID name (definition) | Unit/condition | Condition/specification | SAS control module terminal | ||
|---|---|---|---|---|---|
| CCNT_RCM (Number of continuous DTC) | - |
|
- | ||
| CRSH_ST_D1 (Driver-side side air bag sensor communication state) | OK/FAULT |
|
2Z, 2AA | ||
| CRSH_ST_D2 (Driver-side side air bag sensor circuit state) | OK/FAULT |
|
2Z, 2AA | ||
| CRSH_ST_F1 (Crash zone sensor communication state) | OK/FAULT |
|
1B, 1C | ||
| CRSH_ST_F2 (Crash zone sensor circuit state) | OK/FAULT |
|
1B, 1C | ||
| CRSH_ST_P1 (Passenger-side side air bag sensor communication state) | OK/FAULT |
|
2B, 2C | ||
| CRSH_ST_P2 (Passenger-side side air bag sensor circuit state) | OK/FAULT |
|
2B, 2C | ||
| D_ABAGR2 (Driver-side air bag module (inflator No.2) resistance) | ohms | Under any condition: 1.5-3.7 ohms | 1G, 1J | ||
| D_PTENSFLT (Driver-side pre-tensioner seat belt circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2P, 2S | ||
| DABAGR (Driver-side air bag module (inflator No. 1) resistance) | ohms | Under any condition: 1.5-3.7 ohms | 1S, 1V | ||
| DR_BUKL (Driver-side buckle switch state) | Buckled/Unbuckled |
|
2T | ||
| DR_CURTN (Driver-side curtain air bag module resistance) | ohms | Under any condition: 1.4-3.2 ohms | 2V, 2Y | ||
| DR_PTENS (Driver-side pre-tensioner seat belt resistance) | ohms | Under any condition: 1.5-3.1 ohms | 2P, 2S | ||
| DS_AB (Driver-side side air bag module resistance) | ohms | Under any condition: 1.4-3.2 ohms | 2M, 2O | ||
| DS_AB_ST (Driver-side side air bag module circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2M, 2O | ||
| DS_CURT_ST (Driver-side curtain air bag module circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2V, 2Y | ||
| DS1_STAT (Driver-side air bag module (inflator No. 1) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1S, 1V | ||
| DS2_STAT (Driver-side air bag module (inflator No. 2) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1G, 1J | ||
| DSB_P_ST (Driver-side pre-tensioner seat belt circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2P, 2S | ||
| DTC_CLR_ST(1) (Seat weight sensor status) | Started/Normal End/In Process/OCS Fault | Fault information cleared at seat weight sensor | 1I | ||
| IGN_V_2 (IG1 voltage) | Volts |
|
1W | ||
| OCS_CAL_ST(1) (Seat weight sensor calibration status) | Starting/Normal End/Commanding/NG (Voltage)/NG (Weight)/In Process Timeout/OCS Fault |
|
1I | ||
| OSC_SYS_ST(1) (Seat weight sensor status) | Empty/SMALL/LARGE/Indeterminate/Invalid | Occupant classification status determined by seat weight sensor | 1I | ||
| OCSFLT_CAL (Passenger sensing system calibration status) | OK/FAULT |
|
1I | ||
| OCSFLT_COM (Passenger sensing system communication status) | OK/FAULT |
|
1I | ||
| OCSFLT_L (Passenger sensing system (LH) malfunction status) | OK/FAULT |
|
1I | ||
| OCSFLT_MDL (Passenger sensing system control module malfunction status) | OK/FAULT |
|
1I | ||
| OCSFLT_R (Passenger sensing system (RH) malfunction status) | OK/FAULT |
|
1I | ||
| OCSFLT_SNS (Passenger sensing system malfunction status) | OK/FAULT |
|
1I | ||
| OD_CRST_D1 (On demand driver-side side air bag sensor communication state) | OK/FAULT |
|
2Z, 2AA | ||
| OD_CRST_D2 (On demand driver-side side air bag sensor circuit state) | OK/FAULT |
|
2Z, 2AA | ||
| OD_CRST_F1 (On demand crash zone sensor communication state) | OK/FAULT |
|
1B, 1C | ||
| OD_CRST_F2 (On demand crash zone sensor circuit state) | OK/FAULT |
|
1B, 1C | ||
| OD_CRST_P1 (On demand passenger-side side air bag sensor communication state) | OK/FAULT |
|
2B, 2C | ||
| OD_CRST_P2 (On demand passenger-side side air bag sensor circuit state) | OK/FAULT |
|
2B, 2C | ||
| OD_D_CURT (On demand driver-side curtain air bag module circuit fault state) | SHORT GND SHORT B+ Open SQ LOWERS Normal |
|
2Z, 2AA | ||
| OD_DAB1_ST (On demand driver-side air bag module (inflator No. 1) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1S, 1V | ||
| OD_DAB2_ST (On demand driver-side air bag module (inflator No. 2) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1G, 1J | ||
| OD_DSAB_ST (On demand driver-side side air bag module circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2M, 2O | ||
| OD_P_CURT (On demand passenger-side curtain air bag module circuit fault state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2B, 2C | ||
| OD_PAB1_ST (On demand passenger-side air bag module (inflator No. 1) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1M, 1P | ||
| OD_PAB2_ST (On demand passenger-side air bag module (inflator No. 2) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1A, 1D | ||
| OD_PSAB_ST (On demand passenger-side side air bag module circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2I, 2L | ||
| P_ABAGR2 (Passenger-side air bag module (inflator No. 2) resistance) | ohms | Under any condition: 1.4-2.9 ohms | 1A, 1D | ||
| P_PTENSFLT (Passenger-side pre-tensioner seat belt circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2G, 2J | ||
| PABAGR (Passenger-side air bag module (inflator No. 1) resistance) | ohms | Under any condition: 1.4-2.9 ohms | 1M, 1P | ||
| PS_AB (Passenger-side side air bag module resistance) | ohms | Under any condition: 1.4-3.2 ohms | 2I, 2L | ||
| PS_AB_ST (Passenger-side side air bag module circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2I, 2L | ||
| PS_BUKL (Passenger-side buckle switch state) | Buckled/Unbuckled |
|
2H | ||
| PS_CURT_ST (Passenger-side curtain air bag module circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2A, 2D | ||
| PS_CURTN (Passenger-side curtain air bag module resistance) | ohms | Under any condition: 1.4-3.2 ohms | 2A, 2B | ||
| PS_PTENS (Passenger-side pre-tensioner seat belt resistance) | ohms | Under any condition: 1.5-3.1 ohms | 2G, 2J | ||
| PS_WEIGHT (Seat weight sensor measured weight of passenger) | Kgs | Display of load (body weight) on passenger-side seat | 1I | ||
| PS1_STAT (Passenger-side air bag module (inflator No. 1) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1M, 1P | ||
| PS2_STAT (Passenger-side air bag module (inflator No. 2) circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
1A, 1D | ||
| PSAB_DepSt (Passenger-side air bag module deployment status) | Active/Inactive |
|
1I | ||
| PSB_P_ST (Passenger-side pre-tensioner seat belt circuit state) | SHORT GND/SHORT B+/Open/SQ LOWERS/Normal |
|
2G, 2J | ||
| TRAK_SW (Seat track position sensor state) | Forward/Rearward |
|
2W, 2X | ||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.