SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA20133 MAZDASPEED, 2.3L ENG VIN 3REPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINFOTAINMENTENTERTAINMENT SYSTEMCAR-NAVIGATION UNIT REMOVAL/INSTALLATIONWITH AUDIO UNIT (WITH DISPLAY)
2013 Mazda 3 Mazdaspeed, 2.3L Eng VIN 3

With Audio Unit (With Display)

2013 Mazda 3 Mazdaspeed, 2.3L Eng VIN 3SECTION With Audio Unit (With Display)
  1. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZR 2.0, MZR 2.5] .) (See BATTERY REMOVAL/INSTALLATION [MZR 2.3 DISI TURBO] .) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0] .)
  2. Remove the following parts:
    1. Upper Panel (See UPPER PANEL REMOVAL/INSTALLATION .)
    2. Shift knob (MTX) (See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [G35M-R] .)(See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [G66M-R] .)(See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [A26M-R] .)(See MANUAL TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION [C66M-R] .)
    3. Selector lever knob (ATX) (See AUTOMATIC TRANSAXLE SHIFT MECHANISM REMOVAL/INSTALLATION .)
    4. Shift panel (See SHIFT PANEL REMOVAL/INSTALLATION .)
    5. Side wall (See SIDE WALL REMOVAL/INSTALLATION .)
    6. Console (See CONSOLE REMOVAL/INSTALLATION .)
  3. Remove clips A and B.
    Fig 1: Car-Navigation Unit Wiring Harness Clips A & B
    G00533430Courtesy of MAZDA MOTORS CORP.
  4. Remove the clip C.
  5. Remove the pad.
    Fig 2: Car-Navigation Unit Wiring Harness Clip C & Pad
    G00533431Courtesy of MAZDA MOTORS CORP.
  6. While pressing the clip tabs in the direction of the arrow (1) shown in the figure, press the clip in the direction of arrow (2) to detach the tab of clip D from the console.
  7. Remove the clip D.
    Fig 3: Clip D Removal Procedure
    G00533432Courtesy of MAZDA MOTORS CORP.
  8. Move the car-navigation unit assembly in the direction of arrows (1) and (2) shown in the figure and remove the hook.
  9. Remove the car-navigation unit assembly.
  10. Remove the wiring harness from the bracket hook.
    Fig 4: Car-Navigation Unit Assembly Removal Procedure
    G00533433Courtesy of MAZDA MOTORS CORP.
  11. Disconnect the connector.
  12. Pull the wiring harness from the console.
    Fig 5: Car-Navigation Unit Wiring Harness Removal Procedure
    G00533434Courtesy of MAZDA MOTORS CORP.
  13. Remove the screws.
    Fig 6: Car-Navigation Unit Bracket & Screws
    G00533435Courtesy of MAZDA MOTORS CORP.
  14. Remove the car-navigation unit from the bracket.
  15. Install in the reverse order of removal.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.