SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA20132 TOURING, 1.5L ENG VIN Z, AUTOMATIC TRANSREPAIR AND DIAGNOSISBODY & FRAMEDOOR LOCKSON-BOARD DIAGNOSTIC [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)]DTC TABLE [IMMOBILIZER SYSTEM
2013 Mazda 2 Touring, 1.5L Eng VIN Z, Automatic Trans

DTC Table [Immobilizer System

2013 Mazda 2 Touring, 1.5L Eng VIN Z, Automatic TransSECTION DTC Table [Immobilizer System
NOTE:
  • The security light flashes or illuminates under the following conditions when the ignition is switched to off or ACC.
    • There is a malfunction:
      • DTC 16 or below: Flashes for approx. 1 min  and the DTC flash pattern indicated in the table below repeats 10 times  .
      • DTC 21 or higher: Illuminates for approx. 1 min  and the DTC flash pattern indicated in the table below repeats 10 times  .
      • If more than one DTC is detected, only the DTC with the lowest number is displayed.
    • There is no malfunction
      • The security light illuminates for approx. 3 s  and then turns off.
DTC Description Reference
Security light flashing pattern M-MDS display(1)
Instrument cluster PCM
11
G09133055
 B10D9:87 P1260:00 Communication error with coil antenna (See SECURITY LIGHT: 11, DTC: B10D9:87/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
12
G09133056
 B10D5:13 P1260:00 Coil antenna malfunction (See SECURITY LIGHT: 12, DTC: B10D5:13/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
13
G09133057
 B10D7:05 P1260:00 Key ID number error (See SECURITY LIGHT: 13, DTC: B10D7:05/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
B10D7:94 P1260:00 (See SECURITY LIGHT: 13, DTC: B10D7:94/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
14
G09133058
 B10D7:81 P1260:00 Receiving erratic serial data (See SECURITY LIGHT: 14, DTC: B10D7:81/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
15
G09133059
 B10D7:51 P1260:00 Unprogrammed key ID number (See SECURITY LIGHT: 15, DTC: B10D7:51/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
16
G09133060
 U0100:87 P1260:00 Communication error between instrument cluster and PCM (No response) (See SECURITY LIGHT: 16, DTC: U0100:87/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
21
G09133061
 B10D8:00 P1260:00 Shortage of programmed key (See SECURITY LIGHT: 21, DTC: B10D8:00/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
22
G09133062
 B10DA:51 P1260:00 Communication error to PCM (Data transfer failure) (See SECURITY LIGHT: 22, DTC: B10DA:51/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
23
G09133063
 B10DA:62 P1260:00 Communication error to PCM (Data mis-match) (See SECURITY LIGHT: 23, DTC: B10DA:62/P1260:00 [IMMOBILIZER SYSTEM (KEYLESS ENTRY SYSTEM)] ).
Not illuminated U0001:88 U0073:00 CAN system communication error (HS-CAN) (See FOREWORD [MULTIPLEX COMMUNICATION SYSTEM] ).
U0100:00 - Communication error with PCM
U3000:41 - Instrument cluster internal malfunction (See DTC U3000:41 [INSTRUMENT CLUSTER] ).
(1) The letters at the beginning of each DTC are only displayed when using the M-MDS, and refer to the following: B= Body system, P= Powertrain system, U= Network communication system
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.