SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA20105 SPORT, 2.3 L, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 208 (ENGINE MECHANICAL (SERVICE INFORMATION))TORQUE SPECIFICATIONS
2010 Mazda 5 Sport, 2.3 L, Standard

Torque Specifications

2010 Mazda 5 Sport, 2.3 L, StandardSECTION Torque Specifications
WARNING: This page is about a different car, the 2004 Mazda MPV. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Connector Rod Cap Nuts (1)
Crankshaft Damper Bolt
Step 1 88 (120)
Step 2 Loosen One Full Turn
Step 3 35-39 (47-53)
Step 4 Additional 85-95 Degrees
Crankshaft Main Bearing Cap Bolts (1)
Cylinder Head Bolts (2)
Step 1 24-28 (32-38)
Step 2 Additional 85-95 Degrees
Step 3 Loosen One Full Turn
Step 4 24-28 (32-38)
Step 5 Additional 85-95 Degrees
Step 6 Additional 85-95 Degrees
Drive Belt Tensioner 15-22 (20-30)
EGR Pipe Nuts 26-33 (35-45)
EGR Valve Bolts 14-19 (19-26)
Engine Front Cover Bolts (3) 15-22 (20-30)
Engine Hanger Bolt 73-92 (100-125)
Engine Mount Nuts 50-67(67-93)
Engine Mount Through Bolts 63-86 (85-116)
Exhaust Manifold Nuts (4)(5) 15-18 (20-25)
Flex Plate Bolts (6) 54-64 (73-87)
Generator Bolts 29-24 (40-55)
Generator Bracket Bolts 15-22 (20-30)
Heated Oxygen Sensor 22-36 (29-49)
Knock Sensor 15-22 (20-30)
Oil Pan Drain Plug 16-22 (22-30)
Oil Pan Bolts (7) 15-22 (20-30)
Oil Pressure Switch 9-12 (12-16)
Spark Plug 7-15 (9-20)
Starter Motor Bolts 28-38 (38-51)
Transmission-To-Engine Bolts 28-38 (38-51)
INCH Lbs. (N.m) 
A/C Pipe Stay Nut 80-115 (9-13)
Battery Clamp Nuts 35-62 (4-7)
Battery Tray Bolts & Nut 71-106 (8-12)
Camshaft Bearing Cap Bolts 71-106 (8-12)
Camshaft Position Sensor 71-106 (8-12)
Crankshaft Position Sensor 71-106 (8-12)
Ignition Coil Bolts 53-70 (6-8)
Intake Manifold Bolts (Lower) (8) 71-106 (8-12)
Intake Manifold Bolts (Upper) (9) 71-106 (8-12)
Oil Level Indicator Tube Bolt 71-106 (8-12)
Oil Pump Bolts (10) 71-106 (8-12)
Oil Strainer Bolts 71-106 (8-12)
Oil Strainer Stay Nut
Step 1 133 (15)
Step 2 Additional 45 Degrees
PCM Connector Bolt 26-44 (3-5)
PCM Bracket Nuts 80-115 (9-13)
Radiator Bracket Bolts 71-106 (8-12)
Starter Motor Terminal Nuts 89-106 (10-12)
Thermostat Cover Bolts 71-106 (8-12)
Valve Cover Bolts (11)(12) 71-106 (8-12)
Water Bypass Tube Bolts 71-106 (8-12)
Water Pump Bolt 89 (10)
Water Pump Drive Belt Tensioner Bolt 71-106 (8-12)
(1) Specification not provided from manufacturer.
(2) Tighten bolts in sequence. See Fig 1.
(3) Tighten bolts in sequence. See Fig 2.
(4) Tighten bolts in sequence. See Fig 3.
(5) Tighten bolts in sequence. See Fig 4.
(6) Tighten bolts in sequence. See Fig 5.
(7) Tighten bolts in sequence. See Fig 6.
(8) Tighten bolts in sequence. See Fig 7.
(9) Tighten bolts in sequence. See Fig 8.
(10) Tighten bolts in sequence. See Fig 9.
(11) Tighten bolts in sequence. See Fig 10.
(12) Tighten bolts in sequence. See Fig 11.
Fig 1: Cylinder Head Bolt Tightening Sequence
G00354553Courtesy of MAZDA MOTOR CORP.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.