Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA2008TRIBUTE S SPORT, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1909 (INTERIOR LIGHTING SYSTEM)DIAGNOSIS AND TESTINGINTERIOR LIGHTINGINSPECTION AND VERIFICATION
2008 Mazda Tribute s Sport, 4WD
Inspection and Verification
2008 Mazda Tribute s Sport, 4WDSECTION Inspection and Verification
WARNING: This page is about a different car, the 2010 Mercury Milan, 2010 Lincoln MKZ, and 2010 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
- Verify the customer concern.
- Visually inspect for obvious signs of electrical damage.VISUAL INSPECTION TABLE
Electrical - Smart Junction Box (SJB) fuse(s):
- 9 (15A)
- 10 (15A)
- 25 (10A)
- Wiring, terminals or connectors
- Bulb(s)
- Courtesy lamps
- Map lamps
- Puddle lamp(s)
- Scuff plate lamp(s) (if equipped)
- Luggage compartment lamp
- Vanity lamps
- Instrument panel dimmer switch
- Glove compartment lamp
- Ambient lighting switch (if equipped)
- Smart Junction Box (SJB) fuse(s):
- If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
- If the cause is not visually evident, connect the scan tool to the Data Link Connector (DLC).NOTE: Make sure to use the latest scan tool software release.
- If the scan tool does not communicate with the VCM
:
- Check the VCM connection to the vehicle.
- Check the scan tool connection to the VCM .
- Refer to PINPOINT TEST AF: NO POWER TO THE SCAN TOOL to diagnose no power to the scan tool.
NOTE: The Vehicle Communication Module (VCM) LED prove-out confirms power and ground from the DLC are provided to the VCM . - If the scan tool does not communicate with the vehicle:
- Verify the ignition key is in the ON position.
- Verify the scan tool operation with a known good vehicle.
- Refer to PINPOINT TEST A: THE PCM DOES NOT RESPOND TO THE SCAN TOOL to diagnose no response from the PCM.
- Carry out the network test.
- If the scan tool responds with no communication with the SJB , refer to PINPOINT TEST U: THE SMART JUNCTION BOX (SJB) DOES NOT RESPOND TO THE SCAN TOOL .
- If the network test passes, retrieve and record the continuous memory DTCs.
- Clear the continuous DTCs and carry out the self-test diagnostics for the SJB .
- If the DTCs retrieved are related to the concern, go to DTC TABLES . For all other DTCs, refer to DIAGNOSTIC TROUBLE CODE (DTC) TABLE .
- If no DTCs related to the concern are retrieved, GO to SYMPTOM TABLE .
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.