Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSMAZDA2008TRIBUTE S SPORT, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1620 (BODY PANEL SYSTEM - GENERAL INFORMATION)DIAGNOSTIC TESTSBODY SYSTEMSYMPTOM CHART

2008 Mazda Tribute s Sport, 4WD

Symptom Chart

2008 Mazda Tribute s Sport, 4WDSECTION Symptom Chart

WARNING: This page is about a different car, the 2008 Mercury Mariner and 2008 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Noise, vibration and harshness (NVH) symptoms should be identified using the diagnostic tools that are available. For a list of these tools, an explanation of their uses and a glossary of common terms, refer to NOISE, VIBRATION AND HARSHNESS article. Since it is possible that any one of multiple systems may be the cause of a symptom, it may be necessary to use a process of elimination type of diagnostic approach to pinpoint the responsible system. If this is not the causal system for the symptom, refer back to NOISE, VIBRATION AND HARSHNESS article for the next likely system and continue diagnosis.

Symptom Chart

Condition	Possible Sources	Action
Draft/wind noise and water leak around door perimeter	Loose fit seal	PINCH seal carrier to improve retention on seal flange.
	Seal installed incorrectly	REINSTALL the seal.
	Door misaligned	REALIGN the door. CHECK door gaps and fit in door opening and ADJUST as necessary. REFER to BODY CLOSURES article.
	Scuff plate installed incorrectly	REINSTALL the scuff plate.
	Seal or seal pushpins damaged	INSTALL a new seal/pushpins.
	Sheet metal joints in door or door opening	SEAL leaks with Silicone Gasket and Sealant.
Draft/wind noise and water leak around glass run	Door glass misaligned	ADJUST door glass.
	Glass run installed incorrectly	REINSTALL glass run. INSERT foam in glass run carrier if necessary.
	Leak path behind glass run	INSTALL foam rope behind glass run.
	Glass run channel spread wide	PINCH glass run channel to reduce size of opening.
	Glass run damaged	INSTALL a new glass run.
Draft/wind noise and water leak at inner belt line	Belt line seal installed incorrectly on flange	ADJUST seal. (Do not bend the flange.)
	No contact with side glass	ADJUST door glass.
	No contact with glass runs at both ends of belt line seal	ADJUST belt line seal or ADD foam at seal ends.
	Belt line seal damaged	INSTALL a new seal.
Draft/wind noise and water leak at outer belt line	Belt line seal installed incorrectly on flange (no glass contact)	ADJUST seal.
	Belt line seal does not contact the glass	ADJUST door glass.
	No contact with glass runs at both ends of belt line seal	ADJUST belt line seal or ADD foam at seal ends.
	Belt line seal damaged	INSTALL a new seal.
Draft/wind noise at inner door handle/speaker opening	Hole in weathershield	SEAL hole with suitable tape.
	Weathershield misaligned	REALIGN weathershield. INSTALL a new weathershield if pressure sensitive adhesive fails.
	Exterior door handle seal misaligned/damaged	REALIGN or INSTALL a new seal as necessary. REFER to HANDLES, LOCKS, LATCHES AND ENTRY SYSTEMS article.
	Speaker or speaker seal missing or damaged	REPAIR speaker seal or INSTALL a new door speaker.
Draft/wind noise and water leaks at floor pan and grommets	Missing or damaged plugs/grommets	CHECK plugs/grommets for correct installation or damage. INSTALL new plugs/grommets if necessary.
Road noise	Missing mastic insulators	CHECK for missing mastic insulators. REFER to BODY REPAIRS article.
	Missing body insulators	CHECK for missing body insulators.
Rattles in body/doors and instrument panel	Loose wires/cables	CHECK that all wires/cables are correctly routed and inserted in correct retainers.
	Loose objects/components in door wells, pillars quarter trim panels	CHECK doors by carefully striking underside of doors with a rubber mallet while listening for rattles in doors and pillars. REMOVE or TIGHTEN loose objects/components.
	Buzz from instrument panel components	IDENTIFY which components of the instrument panel are buzzing. SECURE/FASTEN components as necessary, ADD foam or felt as needed if rattle persists.
Door drain holes collecting water	Holes clogged with mud or road tar	CLEAN drain holes of foreign material with a punch or screwdriver. CHECK drain holes regularly.
Wind noise from exterior rear view mirror	Exterior mirror housing misaligned	REALIGN with edges shingled to airflow, with no gaps.
	Mirror sail gasket folded/misaligned	REINSTALL with gasket unfolded and aligned correctly.
	Mirror housing trim cap installed incorrectly	REINSTALL with edges shingled to airflow.
	Air leak through mirror housing hinge	Fully ENGAGE mirror into its operating position. USE foam to block air path through hinge.
	Inner sail trim installed incorrectly	REINSTALL sail trim. ADJUST door trim.
	Inner sail gasket/barrier installed incorrectly	REINSTALL trim cover with gasket/barrier aligned correctly
	Air path through wiring bundle/fastener access holes	BLOCK air path(s) with foam/tape.
	Exposed fastener access hole on mirror housing/sail	INSTALL a new cap if missing.
Rattle/vibration from exterior rear view mirror	Mirror glass adjustment screws loose	REMOVE mirror glass and TIGHTEN mirror glass adjustment motor screws. REFER to REAR VIEW MIRRORS article.
	Mirror mounting nuts loose	TIGHTEN mirror mounting nuts. REFER to REAR VIEW MIRRORS article.
	Aftermarket air deflector/stone shields	If possible, REMOVE aftermarket air deflector/stone shield, then ROAD TEST vehicle. If concern is no longer present, ADVISE customer that aftermarket component was causing concern.
	If equipped with power fold mirrors, power fold mirrors folded/unfolded manually or are not synchronized	If equipped with power fold mirrors, SYNCHRONIZE power fold mirrors. REFER to REAR VIEW MIRRORS article.
Draft/wind noise and water leak around perimeter of all fixed glass	Gaps in the sealant bead	APPLY approved sealant.
	Air traveling up windshield molding along A-pillar	INSTALL foam rope full length of the A-pillar.
	Gaps in sealant bead of windshield	RESEAL windshield glass. REFER to GLASS, FRAMES AND MECHANISMS article.
	Windshield glass misaligned or not installed correctly	REINSTALL windshield glass. REFER to GLASS, FRAMES AND MECHANISMS article.
	Rear hood seal at base of windshield misaligned/damaged	REALIGN or INSTALL a new seal as necessary.
Air leak at cowl	Cowl seal misaligned/damaged	REALIGN or INSTALL a new seal as necessary.
Draft/wind noise and water leak around liftgate perimeter	Loose fit seal	PINCH seal carrier to improve retention on seal flange or INSERT foam in carrier.
	Seal misaligned or installed incorrectly	REINSTALL seal.
	Liftgate misaligned	REALIGN liftgate. CHECK liftgate fit in body opening and ADJUST as necessary.
	Scuff plate misaligned	REINSTALL scuff plate.
	Seal or seal pushpins damaged	INSTALL a new seal.
Draft/water leak or noise from roof opening panel	Roof opening panel/components	REFER to ROOF OPENING PANEL article for diagnosis.
Wind noise created by airflow over or behind body panels	Fender splash shield misaligned	REALIGN fender splash shield.
	Body panel misaligned (exposed edge)	REALIGN appropriate body panel.
	Hood misaligned (front margin)	CHECK hood gaps and fit. ADJUST hood as necessary.
	Front grille edge noise	APPLY foam in hollow areas behind louvers.
Wind noise created by grille opening panel	Grille relationship to leading edge on hood	If possible, ADJUST grille opening panel forward to eliminate wind noise.
	Sharp edges due to material imperfections	REMOVE sharp edges (no damage to visible surface).
Wind noise from air extractor	Air extractor housing seated incorrectly	REINSTALL air extractor housing.
	Air extractor housing or flaps damaged	INSTALL a new air extractor.
Noise from roof rack	Roof rack rails or crossbars loose	TIGHTEN fasteners.
	Roof rack fasteners missing	INSTALL approved fasteners.
	Roof rack crossbars installed backward	REINSTALL crossbars.
	Roof rack rub strips partially lifting from roof	REAPPLY adhesive or fasteners or INSTALL new rub strips as necessary.
	Roof rack gaskets loose or misaligned	REINSTALL gasket.
Wind noise from bug shield/exterior windshield sun visor	Turbulence created by location and shape	Determine if an OEM part or aftermarket. If aftermarket, advise customer accordingly. If OEM, verify correctly installed. If noise is abnormal, repair or replace as required.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.