SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA20086 S SPORT, 4D HATCHBACK, STANDARDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 10 (ON-BOARD DIAGNOSTIC [AUTOMATIC TRANSAXLE FS5A-EL])AFTER REPAIR PROCEDURE [FS5A-EL]
2008 Mazda 6 s Sport, 4D Hatchback, Standard

After Repair Procedure [FS5A-El]

2008 Mazda 6 s Sport, 4D Hatchback, StandardSECTION After Repair Procedure [FS5A-El]
WARNING: This page is about a different variant/trim than selected.
CAUTION:
  • After repairing a malfunction, perform the following procedure to verify that the malfunction has been corrected.
  • When performing this procedure, be sure to drive the vehicle at lawful speed and pay attention to the other vehicles.
  1. Connect the M-MDS the DLC-2.
  2. After the vehicle is identified, select the following items from the initial screen of the M-MDS.
    • When using the IDS (laptop PC)
      1. Select "Self Test".
      2. Select "Modules".
      3. Select "TCM".
    • When using the PDS (Pocket PC)
      1. Select "Module Tests".
      2. Select "TCM".
      3. Select "Self Test".
  3. Verify the DTC according to the directions on the screen.
  4. Press the clear button on the DTC screen to clear the DTC.
  5. Perform the following DTC inspections to ensure that the DTCs have been resolved:
    DTC INSPECTION CHART

    DTC No. inspection
    P0706, P0707, P0708
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle in D range at 20 km/h {12.4 mph} or more for 100 s or more. 
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle in D range at 20 km/h {12.4 mph} or more for 100 s or more. 
    7. Go to Step 5.
    P0711
    1. Start the engine then wait 180 s or more  .
    2. Warm up the engine and ATX.
    3. Drive the vehicle in D range, at within 25-59 km/h {16-36 mph} for 90 s or more. 
    4. Drive the vehicle in D range, at 60 km/h {37 mph} for 60 s or more. 
    5. Turn the ignition switch to the LOCK position.
    6. Start the engine.
    7. Drive the vehicle in D range, at within 25-59 km/h {16-36 mph} for 90 s or more. 
    8. Drive the vehicle in D range, at 60 km/h {37 mph} or more for 60 s or more. 
    9. Go to Step 5.
    P0712, P0713
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle in D range, at 20 km/h {12 mph} or more for 150 s or more. 
    4. Go to Step 5.
    P0715
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle in D range, at 41 km/h {25 mph} or more  for 0.7 s or more. 
    4. Go to Step 5.
    P0720
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions for 4.5 s or more. 
      • Turbine speed (TSS PID): 1,500 RPM or more 
      • Selector lever position: D range, 1GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions for 4.5 s or more. 
      • Turbine speed (TSS PID): 1,500 RPM or more 
      • Selector lever position: D range, 1GR
    7. Go to Step 5.
    P0731
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D or M range, 1GR
      • Throttle opening angle (THOP PID): 4.14% or more 
    4. Go to Step 5.
    P0732
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions 3 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D or M range, 2GR
    4. Go to Step 5.
    P0733
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D or M range, 3GR
    4. Go to Step 5.
    P0734
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 28 km/h {17 mph} or more 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D or M range, 4GR
    4. Go to Step 5.
    P0735
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Selector lever position: D or M range, from 1GR to 5GR
    4. Go to Step 5.
    P0741
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions for 5 s or more. 
      • Vehicle speed (VSS PID): 60-100 km/h {38-62 mph} 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
    4. Go to Step 5.
    P0742
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 70 km/h {43 mph} or less 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
      • Throttle conditions
        • Throttle opening angle (THOP PID) is 6.25% or more  and 5 s or more  have passed.
        • Throttle opening angle (THOP PID) is within 3.13-6.25%  and 3 s or more  have passed.
        • Throttle opening angle is at closed throttle position and 5 s or more  have passed.
    4. Go to Step 5.
    P0744, P0753, P0758, P0763, P0768, P0773, P0778, P0841, P1783, P2709
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle in D range and make sure that the gears shift smoothly from 1GR to 5GR and TCC is operated.
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle in D range and make sure that the gears shift smoothly from 1GR to 5GR and TCC is operated.
    7. Go to Step 5.
    P0745
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle in D range.
    4. Go to Step 5.
    P0751
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions for 15 s or more. 
      • Vehicle speed (VSS PID): 36 km/h {22 mph} or more 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions for 15 s or more. 
      • Vehicle speed (VSS PID): 36 km/h {22 mph} or more 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
    7. Go to Step 5.
    P0752
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Selector lever position: D range
    4. Depress the brake pedal.
    5. Turn the ignition switch to the LOCK position.
    6. Start the engine.
    7. Selector lever position: D range
    8. Depress the brake pedal.
    9. Go to Step 5.
    P0756
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 1GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 1GR
    7. Go to Step 5.
    P0757, P0766
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 28 km/h {17 mph} or more 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle at closed throttle position
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 2GR and 4GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 28 km/h {17 mph} or more 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle at closed throttle position
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 2GR and 4GR
    7. Go to Step 5.
    P0761
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 1GR and 2GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 1GR and 2GR
    7. Go to Step 5.
    P0762
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 26 km/h {16 mph} or more 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 3GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 26 km/h {16 mph} or more 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Differential gear case (output) revolution speed (OSS PID): 35 RPM or more 
      • Selector lever position: D range, 3GR
    7. Go to Step 5.
    P0767
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions for 5 s or more  .
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 3GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions for 5 s or more  .
      • turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 3GR
    7. Go to Step 5.
    P0771
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions for 5 s or more  .
      • Vehicle speed (VSS PID): 60-100 km/h {38-62 mph} 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions for 5 s or more  .
      • Vehicle speed (VSS PID): 60-100 km/h {38-62 mph} 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
    7. Go to Step 5.
    P0772
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 70 km/h {43 mph} or less 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
      • Throttle conditions
        • Throttle opening angle (THOP PID) is 6.25% or more  and 5 s or more  have passed.
        • Throttle opening angle (THOP PID) is within 3.13-6.25%  and 3 s or more  have passed.
        • Throttle opening angle is at closed throttle position and 5 s or more  have passed.
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions.
      • Vehicle speed (VSS PID): 70 km/h {43 mph} or less 
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Selector lever position: D range, 4GR
      • Throttle conditions
        • Throttle opening angle (THOP PID) is 6.25% or more  and 5 s or more  have passed.
        • Throttle opening angle (THOP PID) is within 3.13-6.25%  and 3 s or more  have passed.
        • Throttle opening angle is at closed throttle position and 5 s or more  have passed.
    7. Go to Step 5.
    P0777
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Selector lever position: D range, 5GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Selector lever position: D range, 5GR
    7. Go to Step 5.
    P0791
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle in D range at 40 km/h {25 mph} or more  for 4.5 s or more. 
    4. Go to Step 5.
    P0884
    1. Start the engine.
    2. Idle the engine for 10 s or more.
    3. Idle the engine for 10 s or more. 
    4. Go to Step 7.
    P2707
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Selector lever position: D range, 3GR or 4GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Selector lever position: D range, 3GR or 4GR
    7. Go to Step 5.
    P2708
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Selector lever position: D range, 5GR
    4. Turn the ignition switch to the LOCK position.
    5. Start the engine.
    6. Drive the vehicle under the following conditions 4 times or more.
      • Turbine speed (TSS PID): 225-4,987 RPM 
      • Throttle opening angle (THOP PID): 4.14% or more 
      • Selector lever position: D range, 5GR
    7. Go to Step 5.
    P0894
    1. Start the engine.
    2. Warm up the engine and ATX.
    3. Depress the brake pedal.
    4. Throttle opening angle at closed throttle position.
    5. Shift the selector lever from the N position to the D range and hold for 3 s or more. 
    6. Go to Step 6.
  6. Gradually slow down and stop the vehicle.
  7. Make sure that the repaired DTC does not recur.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.