Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Mazda MX-5 Miata BaseFACTORY OEM SERVICE PROCEDURE
No. 3 PCM Replacement Procedure: Procedure
- Prepare two or more keys to be programmed after the key ID number clearing.
- Connect the WDS or equivalent to the DLC-2. (See WDS OR EQUIVALENT CONNECTING PROCEDURE .)
- Using key 1, turn the ignition switch to the ON position.NOTE:
- Although the security light flashes and DTC 15 or 21 is displayed, this does not indicate an improper procedure. Continue to perform the procedure as indicated.
- Verify that the keyless warning light illuminates for approx. 3 s , and then goes out.
- Select "BODY/SECURITY/PATS (immobilizer) function" from the menu.
- Perform the security access according to the direction of the WDS or equivalent screen. (See SECURITY ACCESS PROCEDURE .)
- Select "Parameter Reset" from the WDS or equivalent screen menu.
- After verifying that the PATS function menu is displayed again on the WDS or equivalent screen, select "Finish (this menu)" to finish the WDS or equivalent procedure.
- After Step 8, wait 5 s or more , and then turn the ignition switch to the LOCK position.
- Using key 1, turn the ignition switch to the ON position.
- After verifying that the security light and keyless warning light illuminates for 3 s or more
turn the ignition switch to the LOCK position and remove key 1.NOTE:
- Although the security light flashes and DTC 21 is displayed, this does not indicate an improper procedure. Continue to perform the procedure as indicated.
- Using key 2, turn the ignition switch to the ON position.
- Verify that the security light and keyless warning light illuminates for approx. 3 s , and then goes out.
- After verifying that the security light goes out, turn the ignition switch to the LOCK position using key 2, and then remove key 2.
- If an additional key needs to be programmed, repeat Steps 13 thru 14 with the additional key being key 3. If the ignition switch is held in the ON position for 1 min or more , the additional key programming procedure according to Steps 13 thru 14 will not be possible. If this occurs, refer to NO.1 ADDITIONAL KEY PROGRAMMING PROCEDURE (USING TWO VALID KEYS) to register any additional keys.
- Start the engine with the key 1.
- Verify that the security light and keyless warning light operate as follows:
- From the point when the ignition switch is turned to the ON position, the security light illuminates for approx. 3 s and goes out.
- The keyless warning light illuminates with the ignition switch turned to the ON position, and after approx. 1 s after the engine is started, it goes out and displays the number of programmed keys.
- After verifying that the keyless warning light goes out, turn the ignition switch to the LOCK position using key 1.
- Repeat Steps 17 thru 18 using key 2 instead of key 1.
- Start the engine with the card key and remove any key from the key cylinder.CAUTION:
- Remove any key from the key cylinder.
- Verify that the security light and keyless warning light operate as follows:
- From the point when the ignition switch is turned to the ON position, the security light illuminates for approx. 3 s , and goes out.
- The keyless warning light illuminates when the ignition switch is turned to the ON position, and after approx. 1 s after the engine is started, it goes out.
- Turn the ignition switch to the LOCK position after verifying that the keyless warning light goes out.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
