Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Mazda MPV DXFACTORY OEM SERVICE PROCEDURE
Specifications Index
MPV SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | GENERAL SERVICING PROCEDURES | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut (Front) | 174-235 Ft. Lbs (236-318 N.m) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | DESCRIPTION & OPERATION | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | MPV | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 14.4-17.6 psi | ||
| Thermostat R & I | NA | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| 2.5L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 20-45 psi (1.4-3.2 kg/cm2 ) at 1500 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 76-81 Ft. Lbs. (103-110 N.m) | ||
| Fuel System | |||
| Pressure Specification | 55-61 psi (3.1-3.6 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE | ||
| Fuel Filter Location and R & I | REMOVAL & INSTALLATION -- MPV | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | See appropriate graphic under FIRING ORDER . | ||
| Spark Plug | |||
| 2.5L V6 (Motorcraft AWSF-32F) | |||
| Gap | .052-.056 in. (1.3-1.4 mm) | ||
| Torque | 7-14 Ft. Lbs (9-20 N.m) | ||
| Starting | |||
| Starter | DESCRIPTION & OPERATION | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 66-86 Ft. Lbs (89-117 N.m) | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.