Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA1995B4000 SE, 2D PICKUP, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSCOMMON SPECS & PROCEDURESSPECIFICATIONS INDEX
1995 Mazda B4000 SE, 2D Pickup, Standard
Specifications Index
1995 Mazda B4000 SE, 2D Pickup, StandardSECTION Specifications Index
(B2300, B3000 & B4000) SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM GENERAL SERVICING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Battery | |||
| B2300 | See BATTERY SPECIFICATIONS table under CAPACITIES . | ||
| B3000 | See BATTERY SPECIFICATIONS table under CAPACITIES . | ||
| B4000 | See BATTERY SPECIFICATIONS table under CAPACITIES . | ||
| Brakes | |||
| Bleeding Sequence | See BRAKE LINE BLEEDING SEQUENCE table under BLEEDING BRAKE SYSTEM . | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | DESCRIPTION & OPERATION | ||
| Torque | GENERATOR & REGULATOR - EXCEPT MITSUBISHI | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 12 psi (0.9 kg/cm2 ) | ||
| Thermostat R & I | n/a | ||
| Water Pump R & I | |||
| 2.3L | WATER PUMP | ||
| 3.0L | WATER PUMP | ||
| 4.0L | WATER PUMP | ||
| Engine Mechanical | |||
| 2.3L 4-Cyl. | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 40-60 psi (2.8-4.2 kg/cm2 ) at 2000 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.0L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil pressure | 40-60 psi (2.8-4.2 kg/cm2 ) at 2500 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 4.0L V6 | |||
| Compression | ENGINE COMPRESSION | ||
| Oil pressure | 40-60 psi (2.8-4.2 kg/cm2 ) at 2000 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.3L 4-Cyl. & 3.0L V6 | 54-64 Ft. Lbs. (73-87 N.m) | ||
| 4.0L V6 | |||
| First Step | 9-11 Ft. Lbs. (12-15 N.m) | ||
| Final Step | 50-55 Ft. Lbs. (68-75 N.m) | ||
| Fuel System | |||
| Pressure Specification | 35-40 psi (2.5-2.8 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE (B2300, B3000 & B4000) | ||
| Fuel Filter Location and R & I | FUEL SYSTEM | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| B2300 | FIRING ORDER | ||
| B3000 | FIRING ORDER | ||
| B4000 | FIRING ORDER | ||
| Ignition Wires (Resistance) | |||
| B2300 | HIGH TENSION WIRE RESISTANCE | ||
| B3000 | HIGH TENSION WIRE RESISTANCE | ||
| B4000 | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | |||
| B2300 | IGNITION SYSTEM | ||
| B3000 | IGNITION SYSTEM | ||
| B4000 | IGNITION SYSTEM | ||
| Spark Plug | |||
| 2.5L 4-Cyl. & 3.0L V6 (Motorcraft AWSF-32PP) | |||
| Gap | Refer to emission control decal located in engine compartment. | ||
| Torque | 7-14 Ft. Lbs. (9-20 N.m) | ||
| 4.0L V6 (Motorcraft AWSF-42PP) | |||
| Gap | Refer to emission control decal located in engine compartment. | ||
| Torque | 10-14 Ft. Lbs. (14-20 N.m) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 85-115 Ft. Lbs. (115-155 N.m) | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.