Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA1995B4000 4WD V6-4.0L OHVREPAIR AND DIAGNOSISSPECIFICATIONSMECHANICAL SPECIFICATIONSENGINESYSTEM SPECIFICATIONSENGINE COMPONENT SPECIFICATIONSCYLINDER HEAD
1995 Mazda B4000 4WD V6-4.0L OHV
Cylinder Head
1995 Mazda B4000 4WD V6-4.0L OHVSECTION Cylinder Head
Cylinder Head:
Combustion Chamber Volume 46.34 - 48.34 cc
Gasket Surface Flatness 0.003 In Any 6 inches - 0.006 Overall
Gasket Surface Finish (RMS) 60 - 150
Rocker Arm:
Shaft Diameter 0.7799 - 0.7811
Bore Diameter 0.7830 - 0.7842
Ratio 1.46:1
Push Rod Runout:
T.I.R Max. 0.020
Valve Guide:
Valve Guide Bore Diameter 0.3174 - 0.3184
Valve Seats:
Width:
Intake 0.060 - 0.079
Exhaust 0.060 - 0.079
Angle 45°
Runout Limit (T.I.R.) 0.0015 Max.
Valve Springs:
Compression Pressure:
60.0 - 68.0 lbs. @ 1.585
138.0 - 149.0 @ 1.222
Free Length:
Approximate 1.91
Assembled Height 1-37/64-1-39/64
Service Limit 10% Pressure Loss @ Specified Length
Out of Square Service Limit 5/64 (0.078)
Valves:
Valve Stem To Guide Clearance:
Intake 0.0008 - 0.0025
Exhaust 0.0018 - 0.0035
Service Clearance 0.0055
Valve Head Diameter:
Intake 43.5 mm (1.71 inch)
Exhaust 34.5 mm (1.36 inch)
Valve Face Runout Limit 0.002 Max.
Valve Face Angle 44°
Valve Stem Diameter:
Standard:
Intake 0.3159 - 0.3167
Exhaust 0.3149 - 0.3235
0.008 Oversize:
Intake 0.3239 - 0.3245
Exhaust 0.3228 - 0.3235
0.016 Oversize:
Intake 0.3318 - 0.3324
Exhaust 0.3307 - 0.3314
Combustion Chamber Volume 46.34 - 48.34 cc
Gasket Surface Flatness 0.003 In Any 6 inches - 0.006 Overall
Gasket Surface Finish (RMS) 60 - 150
Rocker Arm:
Shaft Diameter 0.7799 - 0.7811
Bore Diameter 0.7830 - 0.7842
Ratio 1.46:1
Push Rod Runout:
T.I.R Max. 0.020
Valve Guide:
Valve Guide Bore Diameter 0.3174 - 0.3184
Valve Seats:
Width:
Intake 0.060 - 0.079
Exhaust 0.060 - 0.079
Angle 45°
Runout Limit (T.I.R.) 0.0015 Max.
Valve Springs:
Compression Pressure:
60.0 - 68.0 lbs. @ 1.585
138.0 - 149.0 @ 1.222
Free Length:
Approximate 1.91
Assembled Height 1-37/64-1-39/64
Service Limit 10% Pressure Loss @ Specified Length
Out of Square Service Limit 5/64 (0.078)
Valves:
Valve Stem To Guide Clearance:
Intake 0.0008 - 0.0025
Exhaust 0.0018 - 0.0035
Service Clearance 0.0055
Valve Head Diameter:
Intake 43.5 mm (1.71 inch)
Exhaust 34.5 mm (1.36 inch)
Valve Face Runout Limit 0.002 Max.
Valve Face Angle 44°
Valve Stem Diameter:
Standard:
Intake 0.3159 - 0.3167
Exhaust 0.3149 - 0.3235
0.008 Oversize:
Intake 0.3239 - 0.3245
Exhaust 0.3228 - 0.3235
0.016 Oversize:
Intake 0.3318 - 0.3324
Exhaust 0.3307 - 0.3314
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.