Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSMAZDA1988626 LX, 4D HATCHBACK, 2.2 3REPAIR AND DIAGNOSIS (SINGLE PAGE)BRAKESMECHANICAL - HYDRAULICDISCTORQUE SPECIFICATIONS
1988 Mazda 626 LX, 4D Hatchback, 2.2 3
Torque Specifications
1988 Mazda 626 LX, 4D Hatchback, 2.2 3SECTION Torque Specifications
TIGHTENING SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | ||||
|---|---|---|---|---|---|
| Backing Plate (Rear) | |||||
| All Others | 33-43 (45-58) | ||||
| Caliper Mounting Bracket Bolt | |||||
| 323 | |||||
| Front | 29-36 (39-49) | ||||
| Rear | 36-51 (4969) | ||||
| 626 | |||||
| Front | 58-72 (79-98) | ||||
| Rear | 33-49 (45-67) | ||||
| 929 | |||||
| Front | 58-86 (79-117) | ||||
| Rear | 33-50 (45-68) | ||||
| Caliper Guide Pin or Lock Bolt | |||||
| MX-6 & 626 | |||||
| Front | 23-30 (31-41) | ||||
| Rear | 12-17 (16-23) | ||||
| 323 (Rear) | 12-17 (16-23) | ||||
| RX7 | |||||
| Front (14" Wheel) | 23-30 (31-41) | ||||
| Rear | 22-30 (30-41) | ||||
| 929 | |||||
| Front | 61-69 (83-94) | ||||
| Rear | 12-17 (16-23) | ||||
| 4WD Hub Bolt | 22-25 (30-34) | ||||
| Push Rod Lock Nut | 14-21 (19-29) | ||||
| Rotor-to-Hub Bolts | |||||
| MX-6 & 626 | 36-43 (49-58) | ||||
| 323 | 33-40 (45-54) | ||||
| Stoplight Switch Lock Nut | 10-13 (14-18) | ||||
| Wheel Bearing Lock Nut | |||||
| MX-6 & 626 | |||||
| Rear | (1) | ||||
| 323 | |||||
| Front | 116-174 (158-237) | ||||
| Rear | (1) | ||||
| RX7 | (1) | ||||
| Wheel Lug Nut | |||||
| All Others | 65-87 (88-118) | ||||
| INCH Lbs. (N.m) | |||||
| Master Cylinder Stopper Bolt | 17-22 (2-2.5) | ||||
| Parking Brake Cable Lock Nut | |||||
| All Others | 168-252 (19-29) | ||||
| Wheel Cylinder Mounting Bolt | |||||
| All Others | 84-108 (10-12) | ||||
|
|||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.