Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLINCOLN2016MKZ BASE, 2.0L ENG VIN 9, AWDREPAIR AND DIAGNOSISBODY & FRAMESEATSSEATING SYSTEM - FRONT (EXCEPT HYBRID)DIAGNOSIS AND TESTINGFRONT SEATSDTC CHARTSDTC CHART: SCMH
2016 Lincoln MKZ Base, 2.0L Eng VIN 9, AWD
DTC Chart: SCMH
2016 Lincoln MKZ Base, 2.0L Eng VIN 9, AWDSECTION DTC Chart: SCMH
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B146F:00 | Back Bladder System Electropneumatic Failure: No Sub Type Information | If equipped with redundant seat control switches, GO to Pinpoint Test AN If not equipped with redundant seat control switches, GO to Pinpoint Test AL |
| B146F:04 | Back Bladder System Electropneumatic Failure: System Internal Failure | If equipped with redundant seat control switches, GO to Pinpoint Test AN If not equipped with redundant seat control switches, GO to Pinpoint Test AL |
| B1470:00 | Cushion Bladder System Electropneumatic Failure: No Sub Type Information | If equipped with redundant seat control switches, GO to Pinpoint Test AN If not equipped with redundant seat control switches, GO to Pinpoint Test AL |
| B1470:04 | Cushion Bladder System Electropneumatic Failure: System Internal Failure | If equipped with redundant seat control switches, GO to Pinpoint Test AN If not equipped with redundant seat control switches, GO to Pinpoint Test AL |
| B1471:11 | Multi-Contour Seat Switch Input: Circuit Short To Ground | If equipped with redundant seat control switches, GO to Pinpoint Test AN If not equipped with redundant seat control switches, GO to Pinpoint Test AL |
| B1471:13 | Multi-Contour Seat Switch Input: Circuit Open | If equipped with redundant seat control switches, GO to Pinpoint Test AN If not equipped with redundant seat control switches, GO to Pinpoint Test AL |
| B1471:2A | Multi-Contour Seat Switch Input: Signal Stuck In Range | VERIFY there is no obstruction that may be causing the multi-contour seat switch to be stuck in a certain position. If OK, INSTALL a new seat control switch. Refer to: Front Seat Control Switch . |
| B1473:11 | Pump Driver: Circuit Short To Ground | If equipped with redundant seat control switches, GO to Pinpoint Test AN If not equipped with redundant seat control switches, GO to Pinpoint Test AL |
| U1000:00 | Solid State Driver Protection Actived - Driver Disabled: No Sub Type Information | DIAGNOSE any other related SCMH Diagnostic Trouble Codes (DTCs) first. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U1000:00 returns. INSTALL a new SCMH. Refer to: Driver Multi-Contour Seat Module [SCMG] - Vehicles With: Multi-Contour Seats .. |
| U2100:00 | Initial Configuration Not Complete: no Sub Type Information |
NOTE:
This DTC indicates PMI has not been done to a newly installed module or configuration data has been lost. Using a diagnostic scan tool, CARRY OUT PMI on the SCMH. REPEAT the self-test. If PMI is successful, the DTC will not be present. |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new SCMH. Refer to: Driver Multi-Contour Seat Module [SCMG] - Vehicles With: Multi-Contour Seats . |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.