Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLINCOLN2015MKS BASE, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 18 (ENGINE - 2.0L GTDI)SPECIFICATIONSSPECIFICATIONSTORQUE SPECIFICATIONS
2015 Lincoln MKS Base, AWD
Torque Specifications
2015 Lincoln MKS Base, AWDSECTION Torque Specifications
WARNING: This page is about a different car, the 2015 Lincoln MKT. However, it is still accessible from the selected car via links, so may be relevant.
Torque Specifications
| Description | Nm | lb-ft | lb-in | ||||||
|---|---|---|---|---|---|---|---|---|---|
| A/C compressor bolt | 25 | 18 | - | ||||||
| A/C compressor bracket bolt/nut | 25 | 18 | - | ||||||
| A/C compressor nut | 25 | 18 | - | ||||||
| A/C compressor stud | 9 | - | 80 | ||||||
| A/C compressor tube bracket nut | 15 | - | 133 | ||||||
| A/C compressor tube fitting nut | 15 | - | 133 | ||||||
| Accessory drive belt tensioner bolts | 25 | 18 | - | ||||||
| Balancer unit bolts (1) | - | - | - | ||||||
| Battery terminal nut | 9 | - | 80 | ||||||
| Bellhousing-to-engine bolts | 48 | 35 | - | ||||||
| Bellhousing-to-engine stud bolt | 48 | 35 | - | ||||||
| Bellhousing-to-oil pan bolts | 48 | 35 | - | ||||||
| Brake vacuum pump adapter | 63 | 46 | - | ||||||
| Brake vacuum pump bolts | 10 | - | 89 | ||||||
| Camshaft bearing cap bolts (1) | - | - | - | ||||||
| Camshaft phaser and sprocket bolts (1) | - | - | - | ||||||
| CAC inlet tube bolts | 6 | - | 53 | ||||||
| CAC inlet tube clamp | 8 | - | 71 | ||||||
| CAC intermediate tube mounting bracket fasteners | 8 | - | 71 | ||||||
| CAC outlet tube clamp | 5 | - | 44 | ||||||
| Connecting rod cap bolts (1) | - | - | - | ||||||
| Coolant outlet bolts | 10 | - | 89 | ||||||
| Coolant pump bolts | 10 | - | 89 | ||||||
| Coolant pump pulley bolts | 20 | - | 177 | ||||||
| CKP sensor bolts | 7 | - | 62 | ||||||
| Crankshaft pulley bolt (1) | - | - | - | ||||||
| Crankshaft rear seal with retainer plate bolts (1) | - | - | - | ||||||
| Crankcase vent oil separator bolts | 10 | - | 89 | ||||||
| Cylinder head bolts (1) | - | - | - | ||||||
| CHT sensor | 11 | - | 97 | ||||||
| Engine appearance cover mounting stud | 5 | - | 44 | ||||||
| Engine front cover bolts (1) | - | - | - | ||||||
| Engine lift eye bolts | 47 | 35 | - | ||||||
| Engine mount bolts | 90 | 66 | - | ||||||
| Engine mount nuts | 125 | 92 | - | ||||||
| EOP switch | 15 | - | 133 | ||||||
| Engine plug bolt | 20 | - | 177 | ||||||
| Flexplate bolts (1) | - | - | - | ||||||
| Fuel injection bolts (1) | - | - | - | ||||||
| Fuel injection pump bracket bolts | 17 | - | 150 | ||||||
| Fuel injection pump housing stud bolts (2) | - | - | - | ||||||
| Fuel jumper tube bolt | 8 | - | 71 | ||||||
| Fuel rail bolts (1) | - | - | - | ||||||
| Generator bolt/stud bolt | 25 | 18 | - | ||||||
| Generator terminal nut | 17 | - | 150 | ||||||
| Ground wire bolt (on cylinder head) | 20 | - | 177 | ||||||
| Ground wire nut (on LH inner fender) | 9 | - | 80 | ||||||
| Ground wire nut (on starter stud bolt) | 18 | - | 159 | ||||||
| Ground strap nut (on RH inner fender) | 11 | - | 97 | ||||||
| Ground strap nut (on engine front cover stud bolt) | 9 | - | 80 | ||||||
| High pressure fuel tube bracket bolts | 10 | - | 89 | ||||||
| High pressure fuel tube nuts (1) | - | - | - | ||||||
| Ignition coil-on-plug bolts (1) | - | - | - | ||||||
| Intake manifold bolts (1) | - | - | - | ||||||
| KS | 20 | - | 177 | ||||||
| Main bearing beam bolts (1) | - | - | - | ||||||
| Oil cooler bolt (1) | - | - | - | ||||||
| Oil filter (3) | - | - | - | ||||||
| Oil filter adapter bolts | 25 | 18 | - | ||||||
| Oil pan drain plug | 27 | 20 | - | ||||||
| Oil pan bolts (1) | - | - | - | ||||||
| Oil pan-to-bellhousing bolts | 48 | 35 | - | ||||||
| Oil pump drive chain tensioner shoulder bolts | 10 | - | 89 | ||||||
| Oil pump bolts (1) | - | - | - | ||||||
| Oil pump screen and pickup tube bolts | 10 | - | 89 | ||||||
| Oil pump sprocket bolt | 25 | 18 | - | ||||||
| Piston oil cooler bolts | 10 | - | 89 | ||||||
| RH halfshaft bracket nuts/bolts | 25 | 18 | - | ||||||
| Spark plugs | 12 | - | 106 | ||||||
| Starter motor stud bolt | 35 | 26 | - | ||||||
| Starter wire terminal nut (large) | 12 | - | 106 | ||||||
| Starter wire terminal nut (small) | 5 | - | 44 | ||||||
| Thermostat housing bolts | 10 | - | 89 | ||||||
| Timing chain guide bolts | 10 | - | 89 | ||||||
| Timing chain tensioner bolts | 10 | - | 89 | ||||||
| Torque converter nuts | 40 | 30 | - | ||||||
| Transaxle selector lever cable bracket bolts | 25 | 18 | - | ||||||
| Transaxle support insulator bracket bolt | 80 | 59 | - | ||||||
| Transaxle support insulator bracket nut | 63 | 46 | - | ||||||
| Transaxle support insulator through bolt | 175 | 129 | - | ||||||
| Turbocharger coolant supply banjo bolts | 28 | 21 | - | ||||||
| Turbocharger heat shield bolts | 10 | - | 89 | ||||||
| Turbocharger inlet tube bolt and stud bolt | 5 | - | 44 | ||||||
| Turbocharger inlet/outlet tube clamps | 5 | - | 44 | ||||||
| Turbocharger nuts | 50 | 37 | - | ||||||
| Turbocharger oil return tube bolts | 10 | - | 89 | ||||||
| Turbocharger oil supply banjo bolts | 25 | 18 | - | ||||||
| Turbocharger studs | 17 | - | 150 | ||||||
| Valve cover retainers (1) | - | - | - | ||||||
| VCT solenoid bolts | 10 | - | 89 | ||||||
|
|||||||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.