Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLINCOLN2010MKZ FWD V6-3.5LREPAIR AND DIAGNOSISWINDOWS AND GLASSWINDOWSTECHNICAL SERVICE BULLETINSCUSTOMER INTERESTBODY - BACK GLASS MOULDING LOOSE
2010 Lincoln MKZ FWD V6-3.5L
Body - Back Glass Moulding Loose
2010 Lincoln MKZ FWD V6-3.5LSECTION Body - Back Glass Moulding Loose
TSB 11-7-17
07/22/11
LOOSE REAR WINDOW GLASS MOULDING - BUILT
ON OR BEFORE 617/2011
FORD:
2010-2012 Fusion
LINCOLN:
2010-2012 MKZ
MERCURY:
2010-2011 Milan
This article supersedes TSB 10-16-6 to update the vehicle model years and to add a production fix date.
ISSUE
Some 2010-2011 Milan, 2010-2012 Fusion and MKZ vehicles built on or before 6/7/2011 may exhibit a loose moulding end at the base of the rear window glass.
ACTION
Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE
1. Inspect the moulding ends at the lower edge of the rear window glass.
a. If either end of the moulding is loose, proceed to Step 2.
b. If the moulding is damaged or missing, replace the rear window glass. Refer to Workshop Manual (WSM), Section 501-11.
2. Open the luggage compartment lid and remove moulding from the rear window glass.
3. Clean the glass and moulding with Motorcraft� Ultra-Clear Spray Glass Cleaner. (Figure 1)
4. Starting 1/2" (13 mm) from side edge of glass, apply a small bead of Motorcraft(R) Clear Silicone Rubber Adhesive approximately 3/16" (4 mm) diameter between bottom edge of glass and sheet metal about 5" (127 mm) long. (Figure 2)
5. Center moulding along bottom edge of rear window glass. Starting at one end and working to other, press the moulding onto the glass.
a. Moulding ends should not extend beyond glass corner.
b. Follow Motorcraft� Clear Silicone Rubber adhesive curing directions. Inadequate or incorrect curing of the adhesive will adversely affect rear window glass moulding retention. Failure to follow the adhesive curing directions may cause a repeat loose molding.
6. Close the luggage compartment lid.
Parts Block
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION DESCRIPTION TIME
110717A 2010-2012 Fusion, MKZ, 0.3 Hr.
2010-2011 Milan: Inspect
Moulding, Follow Service
Procedure To Re-Adhere
Moulding (Do Not Use
With Any Other Labor
Operations)
110717B 2010-2012 Fusion, MKZ, 1.8 Hrs.
2010-2011 Milan: Inspect
Moulding, Replace The
Rear Window Glass (Do
Not Use With Any Other
Labor Operations)
DEALER CODING
CONDITION
BASIC PART NO. CODE
5442006 33
Disclaimer
07/22/11
LOOSE REAR WINDOW GLASS MOULDING - BUILT
ON OR BEFORE 617/2011
FORD:
2010-2012 Fusion
LINCOLN:
2010-2012 MKZ
MERCURY:
2010-2011 Milan
This article supersedes TSB 10-16-6 to update the vehicle model years and to add a production fix date.
ISSUE
Some 2010-2011 Milan, 2010-2012 Fusion and MKZ vehicles built on or before 6/7/2011 may exhibit a loose moulding end at the base of the rear window glass.
ACTION
Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE
1. Inspect the moulding ends at the lower edge of the rear window glass.
a. If either end of the moulding is loose, proceed to Step 2.
b. If the moulding is damaged or missing, replace the rear window glass. Refer to Workshop Manual (WSM), Section 501-11.
2. Open the luggage compartment lid and remove moulding from the rear window glass.
3. Clean the glass and moulding with Motorcraft� Ultra-Clear Spray Glass Cleaner. (Figure 1)
4. Starting 1/2" (13 mm) from side edge of glass, apply a small bead of Motorcraft(R) Clear Silicone Rubber Adhesive approximately 3/16" (4 mm) diameter between bottom edge of glass and sheet metal about 5" (127 mm) long. (Figure 2)
5. Center moulding along bottom edge of rear window glass. Starting at one end and working to other, press the moulding onto the glass.
a. Moulding ends should not extend beyond glass corner.
b. Follow Motorcraft� Clear Silicone Rubber adhesive curing directions. Inadequate or incorrect curing of the adhesive will adversely affect rear window glass moulding retention. Failure to follow the adhesive curing directions may cause a repeat loose molding.
6. Close the luggage compartment lid.
Parts Block
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage
IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION DESCRIPTION TIME
110717A 2010-2012 Fusion, MKZ, 0.3 Hr.
2010-2011 Milan: Inspect
Moulding, Follow Service
Procedure To Re-Adhere
Moulding (Do Not Use
With Any Other Labor
Operations)
110717B 2010-2012 Fusion, MKZ, 1.8 Hrs.
2010-2011 Milan: Inspect
Moulding, Replace The
Rear Window Glass (Do
Not Use With Any Other
Labor Operations)
DEALER CODING
CONDITION
BASIC PART NO. CODE
5442006 33
Disclaimer
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.