Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLINCOLN2007MKZ FWD V6-3.5L VIN TREPAIR AND DIAGNOSISBODY AND FRAMERELAYS AND MODULES - BODY AND FRAMESEAT TEMPERATURE CONTROL MODULESERVICE AND REPAIRCLIMATE CONTROLLED SEAT MODULE
2007 Lincoln MKZ FWD V6-3.5L VIN T
Climate Controlled Seat Module
2007 Lincoln MKZ FWD V6-3.5L VIN TSECTION Climate Controlled Seat Module
CLIMATE CONTROLLED SEAT MODULE
Exploded View
Special Tool(s)
Removal
WARNING:
- Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an airbag module. This will reduce the risk of injuring the event of an accidental deployment.
- To reduce the risk of personal injury, do not use any memory saver devices.
NOTE:
- If a seat equipped with a SRS component is being serviced, the SRS must be depowered.
- The air bag warning lamp illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicates SRS fault.
- When installing a new dual climate control seat module (DCSM), it is necessary to carry out programmable module installation (PMI).
- The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
1. Before removing the DCSM, carry out the appropriate steps in the programmable module installation (PMI) procedure.
2. Remove the front seat and depower the supplemental restraint system (SRS).
3. Remove the DCSM from the cushion electrical bracket.
- Release the locking wedges and disconnect the 3 DCSM electrical connectors.
- Remove the 2 rivets and DCSM.
Installation
1. Install the dual climate controlled seat module (DCSM) to the seat.
- Position the DCSM to the electrical bracket and install 2 new rivets.
- Connect the 3 DCSM electrical connectors and locking wedges.
2. Install the front seat and repower the SRS. Do not prove out the SRS at this time.
3. Carry out the Occupant Classification Sensor (OCS) System Zero Seat Weight Test and prove out the SRS.
4. Install the DCSM software data. Carry out the appropriate steps in the PMI procedure.
Front Seat Backrest, Without Fold-Flat (Part 1):
Front Seat Backrest, Without Fold-Flat (Part 2):
Front Seat Backrest, With Fold-Flat (Part 1):
Front Seat Backrest, With Fold-Flat (Part 2):
Driver Seat Cushion (Part 1):
Driver Seat Cushion (Part 2):
Passenger Seat Cushion (Part 1):
Passenger Seat Cushion (Part 2):
Exploded View
Special Tool(s):
Special Tool(s)
Removal
WARNING:
- Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an airbag module. This will reduce the risk of injuring the event of an accidental deployment.
- To reduce the risk of personal injury, do not use any memory saver devices.
NOTE:
- If a seat equipped with a SRS component is being serviced, the SRS must be depowered.
- The air bag warning lamp illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicates SRS fault.
- When installing a new dual climate control seat module (DCSM), it is necessary to carry out programmable module installation (PMI).
- The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
1. Before removing the DCSM, carry out the appropriate steps in the programmable module installation (PMI) procedure.
2. Remove the front seat and depower the supplemental restraint system (SRS).
3. Remove the DCSM from the cushion electrical bracket.
- Release the locking wedges and disconnect the 3 DCSM electrical connectors.
- Remove the 2 rivets and DCSM.
Installation
1. Install the dual climate controlled seat module (DCSM) to the seat.
- Position the DCSM to the electrical bracket and install 2 new rivets.
- Connect the 3 DCSM electrical connectors and locking wedges.
2. Install the front seat and repower the SRS. Do not prove out the SRS at this time.
3. Carry out the Occupant Classification Sensor (OCS) System Zero Seat Weight Test and prove out the SRS.
4. Install the DCSM software data. Carry out the appropriate steps in the PMI procedure.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.