Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DBβ LIVE
HOMESERVICE MANUALSLEXUS2010RX 450H 3.5 BREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINFOTAINMENTAUDIO / VIDEO SYSTEM (W/O NAVIGATION) (DIAGNOSTICS - INTRODUCTION)AUDIO AND VISUAL SYSTEM (W/O NAVIGATION SYSTEM)DIAGNOSTIC TROUBLE CODE CHART (FROM 8/2009)DIAGNOSTIC TROUBLE CODE CHART
2010 Lexus RX 450h 3.5 B
Diagnostic Trouble Code Chart
2010 Lexus RX 450h 3.5 BSECTION Diagnostic Trouble Code Chart
NOTE:
After replacing the radio receiver assembly of vehicles subscribed to pay-type satellite radio broadcasts, the XM radio ID registration is necessary. (w/ SDARS System)
COMMUNICATION DIAGNOSIS
| DTC Code | Detection Item | Trouble Area | See |
|---|---|---|---|
| 01-21 | ROM Error | Radio receiver assembly | Refer to DTC 01-21: ROM Error; DTC 01-22: RAM Error; DTC 01-2E: EEPROM Error |
| 01-22 | RAM Error | Radio receiver assembly | Refer to DTC 01-21: ROM Error; DTC 01-22: RAM Error; DTC 01-2E: EEPROM Error |
| 01-2E | EEPROM Error | Radio receiver assembly | Refer to DTC 01-21: ROM Error; DTC 01-22: RAM Error; DTC 01-2E: EEPROM Error |
| 01-D5 | Absence of Registration Unit | 1. Power source circuit of the component shown by the sub-code 2. AVC-LAN circuit between the radio receiver assembly and component shown by the sub-code 3. Component shown by the sub-code |
Refer to DTC 01-D5: Absence of Registration Unit; DTC 01-D8: No Response for Connection Check; DTC 01-D9: Last Mode Error; DTC 01-DA: No Response Against ON / OFF Command; DTC 01-DB: Mode Status Error; DTC 01-DE: Slave Reset |
| 01-D6 | No Master | 1. Radio receiver assembly power source circuit 2. Power source circuit of the component which has stored this code 3. AVC-LAN circuit between the radio receiver assembly and component which has stored this code 4. Component which has stored this code 5. Radio receiver assembly |
Refer to DTC 01-D6: No Master; DTC 01-D7: Connection Check Error |
| 01-D7 | Connection Check Error | 1. Radio receiver assembly power source circuit 2. Power source circuit of the component which has stored this code 3. AVC-LAN circuit between the radio receiver assembly and component which has stored this code 4. Component which has stored this code 5. Radio receiver assembly |
Refer to DTC 01-D6: No Master; DTC 01-D7: Connection Check Error |
| 01-D8 | No Response for Connection Check | 1. Power source circuit of the component shown by the sub-code 2. AVC-LAN circuit between the radio receiver assembly and component shown by the sub-code 3. Component shown by the sub-code |
Refer to DTC 01-D5: Absence of Registration Unit; DTC 01-D8: No Response for Connection Check; DTC 01-D9: Last Mode Error; DTC 01-DA: No Response Against ON / OFF Command; DTC 01-DB: Mode Status Error; DTC 01-DE: Slave Reset |
| 01-D9 | Last Mode Error | 1. Power source circuit of the component shown by the sub-code 2. AVC-LAN circuit between the radio receiver assembly and component shown by the sub-code 3. Component shown by the sub-code |
Refer to DTC 01-D5: Absence of Registration Unit; DTC 01-D8: No Response for Connection Check; DTC 01-D9: Last Mode Error; DTC 01-DA: No Response Against ON / OFF Command; DTC 01-DB: Mode Status Error; DTC 01-DE: Slave Reset |
| 01-DA | No Response Against ON / OFF Command | 1. Power source circuit of the component shown by the sub-code 2. AVC-LAN circuit between the radio receiver assembly and component shown by the sub-code 3. Component shown by the sub-code |
Refer to DTC 01-D5: Absence of Registration Unit; DTC 01-D8: No Response for Connection Check; DTC 01-D9: Last Mode Error; DTC 01-DA: No Response Against ON / OFF Command; DTC 01-DB: Mode Status Error; DTC 01-DE: Slave Reset |
| 01-DB | Mode Status Error | 1. Power source circuit of the component shown by the sub-code 2. AVC-LAN circuit between the radio receiver assembly and component shown by the sub-code 3. Component shown by the sub-code |
Refer to DTC 01-D5: Absence of Registration Unit; DTC 01-D8: No Response for Connection Check; DTC 01-D9: Last Mode Error; DTC 01-DA: No Response Against ON / OFF Command; DTC 01-DB: Mode Status Error; DTC 01-DE: Slave Reset |
| 01-DC | Transmission Error | If the same sub-code is stored in other components, check power source circuit and communication system of all components shown by sub-code | Refer to DTC 01-DC: Transmission Error |
| 01-DD | Master Reset | 1. Radio receiver assembly power source circuit 2. AVC-LAN circuit between the radio receiver assembly and component which has stored this code 3. Radio receiver assembly 4. Component which has stored this code |
Refer to DTC 01-DD: Master Reset; DTC 01-E1: Voice Processing Device ON Error |
| 01-DE | Slave Reset | 1. Power source circuit of the component shown by the sub-code 2. AVC-LAN circuit between the radio receiver assembly and component shown by the sub-code 3. Component shown by the sub-code |
Refer to DTC 01-D5: Absence of Registration Unit; DTC 01-D8: No Response for Connection Check; DTC 01-D9: Last Mode Error; DTC 01-DA: No Response Against ON / OFF Command; DTC 01-DB: Mode Status Error; DTC 01-DE: Slave Reset |
| 01-DF | Master Error | 1. Radio receiver assembly power source circuit 2. AVC-LAN circuit between the radio receiver assembly and component which has stored this code 3. Radio receiver assembly 4. Component which has stored this code |
Refer to DTC 01-DF: Master Error |
| 01-E0 | Registration Complete Indication Error | - | Refer to DTC 01-E0: Registration Complete Indication Error; DTC 01-E3: Registration Demand Transmission; DTC 01-E4: Multiple Frame Incomplete |
| 01-E1 | Voice Processing Device ON Error | 1. Radio receiver assembly power source circuit 2. AVC-LAN circuit between the radio receiver assembly and component which has stored this code 3. Radio receiver assembly 4. Component which has stored this code |
Refer to DTC 01-DD: Master Reset; DTC 01-E1: Voice Processing Device ON Error |
| 01-E2 | ON / OFF Indication Parameter Error | Radio receiver assembly | Refer to DTC 01-E2: ON / OFF Indication Parameter Error |
| 01-E3 | Registration Demand Transmission | - | Refer to DTC 01-E0: Registration Complete Indication Error; DTC 01-E3: Registration Demand Transmission; DTC 01-E4: Multiple Frame Incomplete |
| 01-E4 | Multiple Frame Incomplete | - | Refer to DTC 01-E0: Registration Complete Indication Error; DTC 01-E3: Registration Demand Transmission; DTC 01-E4: Multiple Frame Incomplete |
| 01-F2 | No Response from Diagnosis Memory Request | Stereo component amplifier assembly |
Refer to DTC 01-F2: No Response from Diagnosis Memory Request; DTC 01-FF: No Response to Diagnosis Request |
| 01-FF | No Response to Diagnosis Request | Stereo component amplifier assembly |
Refer to DTC 01-F2: No Response from Diagnosis Memory Request; DTC 01-FF: No Response to Diagnosis Request |
TELEPHONE
| DTC Code | Detection Item | Trouble Area | See |
|---|---|---|---|
| 57-10 | TEL ECU Malfunction (TEL) | Radio receiver assembly | Refer to DTC 57-10: TEL ECU Malfunction (TEL); DTC 57-47: Bluetooth Module Initialization Failed |
| 57-47 | Bluetooth Module Initialization Failed | Radio receiver assembly | Refer to DTC 57-10: TEL ECU Malfunction (TEL); DTC 57-47: Bluetooth Module Initialization Failed |
RADIO UNIT
IN-DASH CD CHANGER
SPEAKERS
| DTC Code | Detection Item | Trouble Area | See |
|---|---|---|---|
| 74-40 | Short in Speaker Circuit | 1. Wire harness or connector 2. Speaker 3. DCM (Telematics transceiver)*1 4. Stereo component amplifier assembly |
Refer to DTC 74-40: Short in Speaker Circuit |
XM TUNER
MULTI-MEDIA INTERFACE ECU
- *1: w/ Manual (SOS) Switch
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.