2007 Lexus GX 470FACTORY OEM SERVICE PROCEDURE

Knock Sensor, Intake Manifold: Installation

  1. INSTALL KNOCK SENSOR 
    Fig 1: Identifying Knock Sensors
    G04968239Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
    1. Install the 2 knock sensors with the 2 nuts.

      Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) 

    2. Connect the 2 knock sensor connectors.
  2. INSTALL AIR PUMP ASSEMBLY WITH BRACKET (See  INSTALLATION  ) 
  3. INSTALL INTAKE MANIFOLD 
    1. Place 2 new gaskets on the intake manifold.
      Fig 2: Identifying Intake Manifold Gaskets
      G04968240Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
    2. Place the intake manifold on the cylinder heads.
    3. Fig 3: Identifying Cylinder Heads & Bolts
      G04968241Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
    4. Install and uniformly tighten the 6 bolts and 4 nuts in several steps.

      Torque: 18 N*m (185 kgf*cm, 13 ft.*lbf) 

    5. Install the V-bank cover bracket to the intake manifold.

      Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf) 

    6. Install the wire bracket to the intake manifold with the bolt.

      Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf) 

    7. Connect the engine wire to the engine hanger and wire bracket.
      Fig 4: Identifying Cylinder Heads, Bolts & Nuts
      G04968242Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
    8. Connect the wire protector to the intake manifold and cylinder heads with the bolt and nut.
    9. Fig 5: Identifying Cylinder Heads Bolts
      G04968234Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
    10. Install the 2 ground cables with the 2 bolts to the RH and LH cylinder heads.
    11. Connect the 2 water by-pass hoses to the throttle body.
      Fig 6: Connecting Water By-Pass Hoses To Throttle Body
      G04968244Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
    12. Connect the 2 wire clamps to the wire clamp bracket on the RH delivery pipe.
    Fig 7: Locating Wire Clamps To Wire Clamp Bracket On RH Delivery Pipe
    G04968245Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
  4. CONNECT HOSES FORM INTAKE MANIFOLD 
    1. Connect the vacuum hose [A] to the fuel pressure regulator.
    2. Connect the PCV hose [B] to the PCV valve on the LH cylinder head.
    3. Connect the EVAP hose (from the charcoal canister) [C] to the purge VSV.
    4. Connect the 2 vacuum hoses [D] to the VSV for the air injection system.
  5. CONNECT CONNECTORS FROM INTAKE MANIFOLD 
    1. Connect the throttle control connector.
    2. Connect the 2 VSV connectors for the air injection system.
    3. Connect the purge VSV connector.
    4. Connect the 8 injector connectors.
    5. Connect the ECT sensor connector.
    6. Connect the 8 ignition coil connectors.
    7. Connect the 2 air fuel ratio sensor connectors.
  6. INSTALL FUEL HOSE NO.2 
  7. INSTALL FUEL HOSE (See  INSTALLATION  ) 
  8. INSTALL V-BANK COVER SUB-ASSEMBLY (See  INSTALLATION  ) 
  9. ADD ENGINE COOLANT (See  REPLACEMENT  ) 
  10. CHECK FOR ENGINE COOLANT LEAKS (See  ON-VEHICLE INSPECTION  ) 
  11. CHECK FOR FUEL LEAKS (See  ON-VEHICLE INSPECTION  ) 
    Fig 8: Identifying Connectors To Intake Manifold
    G04968246Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.