Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2006RX 400H AWD V6-3.3L (3MZ-FE) HYBRIDREPAIR AND DIAGNOSISPOWER AND GROUND DISTRIBUTIONAUXILIARY POWER OUTLETSERVICE AND REPAIRPOWER POINT SOCKET
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) Hybrid
Power Point Socket
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) HybridSECTION Power Point Socket
REMOVAL
1. REMOVE CONSOLE BOX HOLE COVER
2. REMOVE NO.2 CONSOLE BOX HOLE COVER
3. REMOVE REAR CONSOLE BOX
4. REMOVE CONSOLE COVER LOWER 5. REMOVE POWER POINT SOCKET
a. Turn the power point socket in counterclockwise as shown in the illustration and disengage the claw between the power point socket and the power point socket cover.
b. Push out the power point socket.
c. Align the power point socket with the notch on the power point socket cover, and remove the power point socket.
6. REMOVE POWER POINT SOCKET COVER
a. Disengage the 2 claws and remove the power point socket cover.
INSTALLATION
1. INSTALL POWER POINT SOCKET COVER
a. Engage the 2 claws and install the power point socket cover.
2. INSTALL POWER POINT SOCKET
a. Place the power point socket with the notch on the power point socket cover, and push in the power point socket as hard as possible to install it.
3. INSTALL CONSOLE COVER LOWER
4. INSTALL REAR CONSOLE BOX
5. INSTALL NO.2 CONSOLE BOX HOLE COVER
6. INSTALL CONSOLE BOX HOLE COVER
1. REMOVE CONSOLE BOX HOLE COVER
2. REMOVE NO.2 CONSOLE BOX HOLE COVER
3. REMOVE REAR CONSOLE BOX
4. REMOVE CONSOLE COVER LOWER 5. REMOVE POWER POINT SOCKET
a. Turn the power point socket in counterclockwise as shown in the illustration and disengage the claw between the power point socket and the power point socket cover.
b. Push out the power point socket.
c. Align the power point socket with the notch on the power point socket cover, and remove the power point socket.
6. REMOVE POWER POINT SOCKET COVER
a. Disengage the 2 claws and remove the power point socket cover.
INSTALLATION
1. INSTALL POWER POINT SOCKET COVER
a. Engage the 2 claws and install the power point socket cover.
2. INSTALL POWER POINT SOCKET
a. Place the power point socket with the notch on the power point socket cover, and push in the power point socket as hard as possible to install it.
3. INSTALL CONSOLE COVER LOWER
4. INSTALL REAR CONSOLE BOX
5. INSTALL NO.2 CONSOLE BOX HOLE COVER
6. INSTALL CONSOLE BOX HOLE COVER
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.