Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2006RX 400H AWD V6-3.3L (3MZ-FE) HYBRIDREPAIR AND DIAGNOSISHYBRID DRIVE SYSTEMSRELAYS AND MODULES - HYBRID DRIVEBATTERY BUS MODULESERVICE AND REPAIR
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) Hybrid
Battery Bus Module: Service and Repair
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) HybridSECTION Service and Repair
REMOVAL
1. OBSERVE PRECAUTIONS FOR HIGH-VOLTAGE CIRCUIT INSPECTION AND SERVICE
2. READ OUTPUT DTC
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
4. REMOVE SERVICE PLUG GRIP
5. REMOVE REAR SEAT TRACK BRACKET COVER
6. REMOVE REAR SEAT ASSEMBLY LH
7. REMOVE REAR SEAT TRACK BRACKET COVER
8. REMOVE REAR SEAT ASSEMBLY RH
9. REMOVE AIR INTAKE COVER
10. REMOVE AIR INTAKE COVER CENTER
11. SEPARATE FLOOR CARPET ASSEMBLY FRONT
12. REMOVE REAR CENTER SEAT INNER BELT
13. REMOVE BATTERY CARRIER BRACKET
14. REMOVE BATTERY CARRIER DUCT
15. REMOVE HV BATTERY SERVICE HOLE COVER
16. REMOVE BATTERY COVER SUB-ASSEMBLY
17. REMOVE BATTERY SMART UNIT
NOTE: Wear insulating gloves and protective glasses.
a. Disconnect the 5 connectors and 2 clamps.
b. Remove the 4 bolts and battery smart unit.
INSTALLATION
1. INSTALL BATTERY SMART UNIT
NOTE: Wear insulating gloves and protective glasses.
a. Install the battery smart unit with the 4 bolts.
Torque: 7.5 N.m (76 kgf.cm, 66 in.lbf)
b. Connect the 5 connectors and 2 clamps.
2. CHECK HIGH VOLTAGE CABLE CONNECTION
3. INSTALL BATTERY COVER SUB-ASSEMBLY
4. INSTALL HV BATTERY SERVICE HOLE COVER
5. INSTALL BATTERY CARRIER DUCT
6. INSTALL BATTERY CARRIER BRACKET
7. INSTALL REAR CENTER SEAT INNER BELT
8. INSTALL FLOOR CARPET ASSEMBLY FRONT
9. INSTALL AIR INTAKE COVER CENTER
10. INSTALL AIR INTAKE COVER
11. INSTALL REAR SEAT ASSEMBLY LH
12. INSTALL REAR SEAT TRACK BRACKET COVER
13. INSTALL REAR SEAT ASSEMBLY RH
14. INSTALL REAR SEAT TRACK BRACKET COVER
15. INSPECT SLIDE ADJUSTER LOCK SIMULTANEOUSLY
16. INSTALL SERVICE PLUG GRIP
17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
18. PERFORM INITIALIZATION
Some systems need initialization when reconnecting the battery cable.
1. OBSERVE PRECAUTIONS FOR HIGH-VOLTAGE CIRCUIT INSPECTION AND SERVICE
2. READ OUTPUT DTC
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
4. REMOVE SERVICE PLUG GRIP
5. REMOVE REAR SEAT TRACK BRACKET COVER
6. REMOVE REAR SEAT ASSEMBLY LH
7. REMOVE REAR SEAT TRACK BRACKET COVER
8. REMOVE REAR SEAT ASSEMBLY RH
9. REMOVE AIR INTAKE COVER
10. REMOVE AIR INTAKE COVER CENTER
11. SEPARATE FLOOR CARPET ASSEMBLY FRONT
12. REMOVE REAR CENTER SEAT INNER BELT
13. REMOVE BATTERY CARRIER BRACKET
14. REMOVE BATTERY CARRIER DUCT
15. REMOVE HV BATTERY SERVICE HOLE COVER
16. REMOVE BATTERY COVER SUB-ASSEMBLY
17. REMOVE BATTERY SMART UNIT
NOTE: Wear insulating gloves and protective glasses.
a. Disconnect the 5 connectors and 2 clamps.
b. Remove the 4 bolts and battery smart unit.
INSTALLATION
1. INSTALL BATTERY SMART UNIT
NOTE: Wear insulating gloves and protective glasses.
a. Install the battery smart unit with the 4 bolts.
Torque: 7.5 N.m (76 kgf.cm, 66 in.lbf)
b. Connect the 5 connectors and 2 clamps.
2. CHECK HIGH VOLTAGE CABLE CONNECTION
3. INSTALL BATTERY COVER SUB-ASSEMBLY
4. INSTALL HV BATTERY SERVICE HOLE COVER
5. INSTALL BATTERY CARRIER DUCT
6. INSTALL BATTERY CARRIER BRACKET
7. INSTALL REAR CENTER SEAT INNER BELT
8. INSTALL FLOOR CARPET ASSEMBLY FRONT
9. INSTALL AIR INTAKE COVER CENTER
10. INSTALL AIR INTAKE COVER
11. INSTALL REAR SEAT ASSEMBLY LH
12. INSTALL REAR SEAT TRACK BRACKET COVER
13. INSTALL REAR SEAT ASSEMBLY RH
14. INSTALL REAR SEAT TRACK BRACKET COVER
15. INSPECT SLIDE ADJUSTER LOCK SIMULTANEOUSLY
16. INSTALL SERVICE PLUG GRIP
17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
18. PERFORM INITIALIZATION
Some systems need initialization when reconnecting the battery cable.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.