Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2006RX 400H AWD V6-3.3L (3MZ-FE) HYBRIDREPAIR AND DIAGNOSISBRAKES AND TRACTION CONTROLANTILOCK BRAKES / TRACTION CONTROL SYSTEMSTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESFREEZE FRAME DATA
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) Hybrid
Freeze Frame Data
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) HybridSECTION Freeze Frame Data
FREEZE FRAME DATA
1. FREEZE FRAME DATA
a. Whenever a DTC is detected or the ABS operates, the skid control ECU stores the current vehicle (sensor) state as freeze frame data.
The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to the ON position since the last time the ABS was activated.
HINT:
^ However, if the vehicle is stopped or at low speed (4.3 mph (7 km/h) or less), or if a DTC is detected, the skid control ECU will stop counting the number since then.
^ Freeze frame data at the time the ABS operates: The skid control ECU stores and updates data whenever the ABS system operates. When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is erased.
^ Freeze frame data at the time a DTC is detected: When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.
b. Connect the intelligent tester to the DLC3.
c. Turn the ignition switch on.
d. From the display on the tester, select the FREEZE FRAME DATA.
1. FREEZE FRAME DATA
a. Whenever a DTC is detected or the ABS operates, the skid control ECU stores the current vehicle (sensor) state as freeze frame data.
The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to the ON position since the last time the ABS was activated.
HINT:
^ However, if the vehicle is stopped or at low speed (4.3 mph (7 km/h) or less), or if a DTC is detected, the skid control ECU will stop counting the number since then.
^ Freeze frame data at the time the ABS operates: The skid control ECU stores and updates data whenever the ABS system operates. When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is erased.
^ Freeze frame data at the time a DTC is detected: When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.
b. Connect the intelligent tester to the DLC3.
c. Turn the ignition switch on.
FREEZE FRAME DATA:
FREEZE FRAME DATA:
FREEZE FRAME DATA:
d. From the display on the tester, select the FREEZE FRAME DATA.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.