Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSLEXUS2006RX 400H AWD V6-3.3L (3MZ-FE) HYBRIDREPAIR AND DIAGNOSISACCESSORIES AND OPTIONAL EQUIPMENTANTITHEFT AND ALARM SYSTEMSKEYLESS ENTRYSERVICE AND REPAIR
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) Hybrid
Keyless Entry: Service and Repair
2006 Lexus RX 400h AWD V6-3.3L (3MZ-FE) HybridSECTION Service and Repair
DOOR CONTROL RECEIVER
REMOVAL
1. REMOVE TONNEAU COVER ASSEMBLY
2. REMOVE DECK BOARD SUB-ASSEMBLY
3. REMOVE DECK FLOOR BOX FRONT
4. REMOVE DECK FLOOR BOX REAR
5. REMOVE NO.3 DECK BOARD SUB-ASSEMBLY
6. REMOVE NO.2 DECK BOARD SUB-ASSEMBLY
7. REMOVE BACK DOOR WEATHERSTRIP
8. REMOVE REAR FLOOR FINISH PLATE
9. REMOVE DECK SIDE TRIM BOX LH
10. REMOVE DECK SIDE TRIM BOX RH
11. REMOVE REAR DOOR SCUFF PLATE
12. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP
13. REMOVE DECK SIDE TRIM COVER
14. SEPARATE REAR NO.1 SEAT BELT ASSEMBLY OUTER
15. REMOVE REAR SEAT SIDE COVER
16. REMOVE REAR FLOOR FINISH SIDE PLATE
17. REMOVE ROPE HOOK
18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY
19. REMOVE NO.2 ROOM LIGHT ASSEMBLY
20. REMOVE ROOF SIDE GARNISH ASSEMBLY INNER
21. REMOVE DOOR CONTROL RECEIVER
a. Disconnect the connector.
b. Remove the bolt and the door control receiver.
INSTALLATION
1. INSTALL DOOR CONTROL RECEIVER
a. Install the door control receiver with the bolt.
b. Connect the connector.
2. INSTALL ROOF SIDE GARNISH ASSEMBLY INNER
3. INSTALL NO.2 ROOM LIGHT ASSEMBLY
4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY
5. INSTALL ROPE HOOK
6. INSTALL REAR FLOOR FINISH SIDE PLATE
7. INSTALL REAR SEAT SIDE COVER
8. INSTALL REAR NO.1 SEAT BELT ASSEMBLY OUTER
9. INSTALL DECK SIDE TRIM COVER
10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP
11. INSTALL REAR DOOR SCUFF PLATE
12. INSTALL DECK SIDE TRIM BOX LH
13. INSTALL DECK SIDE TRIM BOX RH
14. INSTALL REAR FLOOR FINISH PLATE
15. INSTALL BACK DOOR WEATHERSTRIP
16. INSTALL NO.3 DECK BOARD SUB-ASSEMBLY
17. INSTALL NO.2 DECK BOARD SUB-ASSEMBLY
18. INSTALL DECK FLOOR BOX REAR
19. INSTALL DECK FLOOR BOX FRONT
20. INSTALL DECK BOARD SUB-ASSEMBLY
21. INSTALL TONNEAU COVER ASSEMBLY
REMOVAL
1. REMOVE TONNEAU COVER ASSEMBLY
2. REMOVE DECK BOARD SUB-ASSEMBLY
3. REMOVE DECK FLOOR BOX FRONT
4. REMOVE DECK FLOOR BOX REAR
5. REMOVE NO.3 DECK BOARD SUB-ASSEMBLY
6. REMOVE NO.2 DECK BOARD SUB-ASSEMBLY
7. REMOVE BACK DOOR WEATHERSTRIP
8. REMOVE REAR FLOOR FINISH PLATE
9. REMOVE DECK SIDE TRIM BOX LH
10. REMOVE DECK SIDE TRIM BOX RH
11. REMOVE REAR DOOR SCUFF PLATE
12. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP
13. REMOVE DECK SIDE TRIM COVER
14. SEPARATE REAR NO.1 SEAT BELT ASSEMBLY OUTER
15. REMOVE REAR SEAT SIDE COVER
16. REMOVE REAR FLOOR FINISH SIDE PLATE
17. REMOVE ROPE HOOK
18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY
19. REMOVE NO.2 ROOM LIGHT ASSEMBLY
20. REMOVE ROOF SIDE GARNISH ASSEMBLY INNER
21. REMOVE DOOR CONTROL RECEIVER
a. Disconnect the connector.
b. Remove the bolt and the door control receiver.
INSTALLATION
1. INSTALL DOOR CONTROL RECEIVER
a. Install the door control receiver with the bolt.
b. Connect the connector.
2. INSTALL ROOF SIDE GARNISH ASSEMBLY INNER
3. INSTALL NO.2 ROOM LIGHT ASSEMBLY
4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY
5. INSTALL ROPE HOOK
6. INSTALL REAR FLOOR FINISH SIDE PLATE
7. INSTALL REAR SEAT SIDE COVER
8. INSTALL REAR NO.1 SEAT BELT ASSEMBLY OUTER
9. INSTALL DECK SIDE TRIM COVER
10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP
11. INSTALL REAR DOOR SCUFF PLATE
12. INSTALL DECK SIDE TRIM BOX LH
13. INSTALL DECK SIDE TRIM BOX RH
14. INSTALL REAR FLOOR FINISH PLATE
15. INSTALL BACK DOOR WEATHERSTRIP
16. INSTALL NO.3 DECK BOARD SUB-ASSEMBLY
17. INSTALL NO.2 DECK BOARD SUB-ASSEMBLY
18. INSTALL DECK FLOOR BOX REAR
19. INSTALL DECK FLOOR BOX FRONT
20. INSTALL DECK BOARD SUB-ASSEMBLY
21. INSTALL TONNEAU COVER ASSEMBLY
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.