SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSKIA2020SOUL LX, STANDARD TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)BODY & FRAMEWINDOWSLIFTGATE WINDOW GLASSREPAIR PROCEDURESINSTALLATION
2020 Kia Soul LX, Standard Trans

Repair Procedures: Installation

2020 Kia Soul LX, Standard TransSECTION Installation
  1. Using a cutting knife (A), remove the remaining sealant (B) on the body panel.
    CAUTION: Put on gloves to protect your hands.
    G13282154Courtesy of KIA MOTORS AMERICA, INC.
  2. Apply the body primer to the bonding surface of body panel.
    CAUTION:
    • Be careful not to touch the surface covered with the primer because touching it may lead to water leaks after installing the liftgate window glass.
    • Do not apply the body primer to the glass.
    • Remove any foreign materials from the primer-covered surface.
    G13282155Courtesy of KIA MOTORS AMERICA, INC.
  3. Apply the glass primer to the outer edge of liftgate window glass (A).
    CAUTION:
    • Be careful not to touch the surface covered with the primer because touching it may lead to water leaks after installing the liftgate window glass.
    • Remove any foreign materials from the primer-covered surface.
    G13282156Courtesy of KIA MOTORS AMERICA, INC.
  4. Using a sealant gun, apply the sealant (B) to the edge of rear liftgate window glass (A).
    G13282157Courtesy of KIA MOTORS AMERICA, INC.
  5. Using the glass holder, adjust the liftgate window glass (A) to fit the alignment marks (B) on the body and lightly push the liftgate window glass to make the edges fully seated on the bonding surface of body.
    NOTE: When installing the liftgate window glass (A), be sure to fit the protruding part (C) on the reverse side of the glass into the groove on the body frame.
    G13282158Courtesy of KIA MOTORS AMERICA, INC.
  6. Insert the hot wire connector (A).

    [LH] 

    G13282159Courtesy of KIA MOTORS AMERICA, INC.

    [RH] 

    G13282160Courtesy of KIA MOTORS AMERICA, INC.
  7. To make sure that the applied sealant is completely hardened, leave the car on a flat surface for at least 3 to 4 hours after installing the liftgate window glass.

    Information 

    • If driving the car is inevitable, drive at a low speed for at least 8 hours.
    • Advise the driver to avoid aggressive driving or driving on rough roads for 2-3 days after installing the liftgate window glass.
  8. Conduct a leak testing.

    Information 

    • The leak testing shall be conducted at least 4 hours after the liftgate window glass installation is completed.
    • Do not directly spray the high-pressure water to the joint area.
  9. Install the rear wiper motor.

    (Refer to Body Electrical System - "WIPER MOTOR ")

  10. Install the liftgate trim.

    (Refer to Liftgate - "LIFTGATE TRIM ")

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.