Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Kia Niro EXFACTORY OEM SERVICE PROCEDURE
DTC Index
DTC INDEX
| DTC | Description |
|---|---|
| DTC P2243 | 00: O2 Sensor Reference Voltage Circuit/Open (Bank 1 / Sensor 1) |
| DTC P2251 | 00: O2 Sensor Reference Ground Circuit/Open (Bank 1 / Sensor 1) |
| DTC P2270 | 00: O2 Sensor Signal Stuck Lean (Bank 1 / Sensor 2) |
| DTC P2271 | 00: O2 Sensor Signal Stuck Rich (Bank 1 / Sensor 2) |
| DTC P2297 | 00: O2 Sensor Out of Range During Deceleration - (Bank 1 / Sensor 1) |
| DTC P2414 | 00: O2 Sensor Exhaust Sample Error (Bank 1 / Sensor 1) |
| DTC P2418 | 00: Evaporative Emission System Switching Valve Control Circuit/Open |
| DTC P2419 | 00: Evaporative Emission System Switching Valve Control Circuit - Low |
| DTC P2420 | 00: Evaporative Emission System Switching Valve Control Circuit - High |
| DTC P2451 | 00: Evaporative Emission System Switching Valve Stuck Closed |
| DTC P2540 | 00: Low Pressure Fuel System Sensor Circuit Range/Performance |
| DTC P2541 | 00: Low Pressure Fuel System Sensor Circuit - Low |
| DTC P2542 | 00: Low Pressure Fuel System Sensor Circuit - High |
| DTC P2600 | 00: Coolant Pump 'A' Control Circuit/Open |
| DTC P2601 | 00: Coolant Pump 'A' Control Circuit Range/Performance |
| DTC P2610 | 00: ECM/PCM Internal Engine OFF Timer Performance |
| DTC P261F | 00: Coolant Pump 'A' Control Circuit Stuck ON |
| DTC P2626 | 00: O2 Sensor Pumping Current Trim Circuit/Open (Bank 1 / Sensor 1) |
| DTC P262B | 00: Control Module Power OFF Timer Performance |
| DTC P26D0 | 00: Engine Coolant Pump Control Module System Voltage Low |
| DTC P26D1 | 00: Engine Coolant Pump Control Module System Voltage High |
| DTC P3190 | 00: Poor Engine Power |
| DTC U0001 | 00: High Speed CAN Communication BUS OFF (C-CAN) |
| DTC U0101 | 00: Lost Communication With TCM (C-CAN) |
| DTC U0109 | 00: Lost Communication With Fuel Pump Control Module |
| DTC U0110 | 00: Lost Communication With Drive Motor Control Module |
| DTC U0111 | 00: Lost Communication With Battery Energy Control Module 'A' (C-CAN) |
| DTC U0293 | 00: Lost Communication With Hybrid Powertrain Control Module (C-CAN) |
| DTC U029F | 00: Lost Communication With Evaporative Emission System Leak Detection Control Module Guide |
| DTC U0456 | 00: Invalid Data Received From Coolant Temperature Control Module |
| DTC U1001 | 00: High Speed CAN Communication BUS (H-CAN) |
| DTC U1003 | 00: Lost Communication With TCM (H-CAN) |
| DTC U1004 | 00: Lost Communication With Hybrid Powertrain Control Module (H-CAN) |
| DTC U1008 | 00: Lost Communication With Radiator Shutter (Active Air Flap) (C-CAN) |
| DTC U1111 | 00: LIN Message Time-Out With EBS |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
