Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSKIA2015RIO SX, 4D HATCHBACKREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCESYSTEMENGINE CONTROL SYSTEM DIAGNOSIS (1 OF 2)DTC INDEX
2015 Kia Rio SX, 4D Hatchback
DTC Index
2015 Kia Rio SX, 4D HatchbackSECTION DTC Index
DTC INDEX
| DTC | Description |
|---|---|
| DTC P0011 | 'A' Camshaft Position-Timing Over-Advanced or System Performance (Bank 1) |
| DTC P0014 | 'B' Camshaft Position-Timing Over-Advanced or System Performance_Bank 1 |
| DTC P0016 | Crankshaft Position-Camshaft Position Correlation (Bank 1 Sensor A) |
| DTC P0017 | Crankshaft Position-Camshaft Position Correlation (Bank 1 Sensor B) |
| DTC P0030 | HO2S Heater Control Circuit (Bank 1_Sensor 1) |
| DTC P0031 | HO2S Heater Control Circuit Low (Bank 1_Sensor 1) |
| DTC P0032 | HO2S Heater Control Circuit High (Bank 1_Sensor 1) |
| DTC P0036 | HO2S Heater Control Circuit (Bank 1_Sensor 2) |
| DTC P0037 | HO2S Heater Control Circuit Low (Bank 1_Sensor 2) |
| DTC P0038 | HO2S Heater Control Circuit High (Bank 1_Sensor 2) |
| DTC P0075 | Intake Valve Control Solenoid Circuit (Bank 1) |
| DTC P0076 | Intake Valve Control Solenoid Circuit-Low (Bank 1) |
| DTC P0077 | Intake Valve Control Solenoid Circuit-High (Bank 1) |
| DTC P0078 | Exhaust Valve Control Solenoid Circuit (Bank 1) |
| DTC P0079 | Exhaust Valve Control Solenoid Circuit Low (Bank 1) |
| DTC P0080 | Exhaust Valve Control Solenoid Circuit High (Bank 1) |
| DTC P0087 | Fuel Rail/System Pressure - Too Low |
| DTC P0088 | Fuel Rail/System Pressure - Too High |
| DTC P0089 | Fuel Pressure Regulator 1 Performance |
| DTC P0090 | Fuel Pressure Regulator 1 Control Circuit/Open |
| DTC P0091 | Fuel Pressure Regulator 1 Control Circuit Low |
| DTC P0092 | Fuel Pressure Regulator 1 Control Circuit High |
| DTC P0106 | Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance |
| DTC P0107 | Manifold Absolute Pressure/Barometric Pressure Circuit Low Input |
| DTC P0108 | Manifold Absolute Pressure/Barometric Pressure Circuit High Input |
| DTC P0111 | Intake Air Temperature Sensor 1 Circuit Range/Performance |
| DTC P0112 | Intake Air Temperature Sensor 1 Circuit Low Input |
| DTC P0113 | Intake Air Temperature Sensor 1 Circuit High Input |
| DTC P0116 | Engine Coolant Temperature Circuit Range/Performance |
| DTC P0117 | Engine Coolant Temperature Circuit Low Input |
| DTC P0118 | Engine Coolant Temperature Circuit High Input |
| DTC P0119 | Engine Coolant Temperature Circuit Intermittent |
| DTC P0121 | Throttle/Pedal Position Sensor/Switch 'A' Circuit Range/Performance |
| DTC P0122 | Throttle Position Sensor 1 Signal Circuit Low Input |
| DTC P0123 | Throttle Position Sensor 1 Signal Circuit High Input |
| DTC P0128 | Coolant Thermostat (Coolant Temperature below Thermostat Regulating Temperature) |
| DTC P0130 | O2 Sensor Circuit (Bank 1/ Sensor 1) |
| DTC P0131 | O2 Sensor Circuit Low Voltage (Bank 1/ Sensor 1) |
| DTC P0132 | O2 Sensor Circuit High Voltage (Bank 1/ Sensor 1) |
| DTC P0133 | O2 Sensor Circuit Slow Response (Bank 1/ Sensor 1) |
| DTC P0135 | O2 Sensor Heater Circuit (Bank 1/ Sensor 1) |
| DTC P0136 | O2 Sensor Circuit (Bank 1/ Sensor 2) |
| DTC P0137 | O2 Sensor Circuit Low Voltage (Bank 1/ Sensor 2) |
| DTC P0138 | O2 Sensor Circuit High Voltage (Bank 1/ Sensor 2) |
| DTC P0139 | O2 Sensor Circuit Slow Response (Bank 1/ Sensor 2) |
| DTC P0141 | O2 Sensor Heater Circuit (Bank 1/ Sensor 2) |
| DTC P0191 | Fuel Rail Pressure Sensor Circuit Range/Performance |
| DTC P0192 | Fuel Rail Pressure Sensor Circuit Low Input |
| DTC P0193 | Fuel Rail Pressure Sensor Circuit High Input |
| DTC P0201 | Injector Circuit/Open-Cylinder 1 |
| DTC P0202 | Injector Circuit/Open-Cylinder 2 |
| DTC P0203 | Injector Circuit/Open-Cylinder 3 |
| DTC P0204 | Injector Circuit/Open-Cylinder 4 |
| DTC P0221 | Throttle/Pedal Position Sensor/Switch 'B' Circuit Range/Performance |
| DTC P0222 | Throttle/Pedal Position Sensor/Switch 'B' Circuit Low Input |
| DTC P0223 | Throttle/Pedal Position Sensor/Switch 'B' Circuit High Input |
| DTC P0230 | Fuel Pump Primary Circuit |
| DTC P0261 | Cylinder 1 Injector Circuit Low |
| DTC P0262 | Cylinder 1 Injector Circuit High |
| DTC P0263 | Cylinder 1-Injector Circuit Balance (Load Drop is Detected) |
| DTC P0264 | Cylinder 2 Injector Circuit Low |
| DTC P0265 | Cylinder 2 Injector Circuit High |
| DTC P0266 | Cylinder 2-Injector Circuit Balance (Load Drop is Detected) |
| DTC P0267 | Cylinder 3 Injector Circuit Low |
| DTC P0268 | Cylinder 3 Injector Circuit High |
| DTC P0269 | Cylinder 3-Injector Circuit Balance (Load Drop is Detected) |
| DTC P0270 | Cylinder 4 Injector Circuit Low |
| DTC P0271 | Cylinder 4 Injector Circuit High |
| DTC P0272 | Cylinder 4-Injector Circuit Balance (Load Drop is Detected) |
| DTC P0300 | Random/Multiple Cylinder Misfire Detected |
| DTC P0301 | Cylinder 1-Misfire detected |
| DTC P0302 | Cylinder 2-Misfire detected |
| DTC P0303 | Cylinder 3-Misfire detected |
| DTC P0304 | Cylinder 4-Misfire detected |
| DTC P0326 | Knock Sensor 1 Circuit Range/Performance (Bank 1) |
| DTC P0335 | Crankshaft Position Sensor 'A' Circuit |
| DTC P0336 | Crankshaft Position Sensor 'A' Circuit Range/Performance |
| DTC P0340 | Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor) |
| DTC P0341 | Camshaft Position Sensor A Circuit Range/Performance (Bank 1) |
| DTC P0365 | Camshaft Position Sensor B Circuit Malfunction (Bank 1) |
| DTC P0366 | Camshaft Position Sensor 'B' Circuit Range/Performance (Bank 1) |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.