Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSKIA2010RONDO LX, 2.7 6REPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXANTI-LOCK BRAKE SYSTEM/ELECTRONIC STABILITY CONTROL (ABS/ESC) DTCS
2010 Kia Rondo LX, 2.7 6
Anti-Lock Brake System/Electronic Stability Control (Abs/ESC) DTCS
2010 Kia Rondo LX, 2.7 6SECTION Anti-Lock Brake System/Electronic Stability Control (Abs/ESC) DTCS
ANTI-LOCK BRAKE SYSTEM/ELECTRONIC STABILITY CONTROL (ABS/ESC) DIAGNOSTIC TROUBLE CODES (DTC) LIST
| DTC | Description |
|---|---|
| DTC C1101 | Battery voltage high |
| DTC C1102 | Battery voltage low |
| DTC C1112 | Sensor power voltage |
| DTC C1200 | Wheel speed sensor front-LH open-short |
| DTC C1201 | Wheel speed sensor front-LH range - performance - intermittent |
| DTC C1202 | Wheel speed sensor front-LH invalid-no signal |
| DTC C1203 | Wheel speed sensor front-RH open-short |
| DTC C1204 | Wheel speed sensor front-RH range-- performance --intermittent |
| DTC C1205 | Wheel speed sensor front-RH invalid-no signal |
| DTC C1206 | Wheel speed sensor rear-LH open-short |
| DTC C1207 | Wheel speed sensor rear-LH range-performance-intermittent |
| DTC C1208 | Wheel speed sensor rear-LH invalid-no signal |
| DTC C1209 | Wheel speed sensor rear-RH open-short |
| DTC C1210 | Wheel speed sensor rear-RH range-- performance-- intermittent |
| DTC C1211 | Wheel speed sensor rear-RH invalid-no signal |
| DTC C1235 | Primary pressure sensor - electrical |
| DTC C1237 | Primary pressure sensor - signal |
| DTC C1259 | Steering sensor - electrical |
| DTC C1260 | Steering sensor circuit - signal |
| DTC C1282 | Yaw rate and lateral G sensor - electrical |
| DTC C1283 | Yaw rate and lateral G sensor - signal |
| DTC C1503 | ESP switch error |
| DTC C1513 | Brake switch error |
| DTC C1604 | ECU Hardware Error |
| DTC C1605 | CAN Hardware Error |
| DTC C1611 | CAN time-out EMS |
| DTC C1612 | CAN time-out TCU |
| DTC C1613 | CAN wrong message |
| DTC C1616 | CAN bus off |
| DTC C2112 | Valve relay error |
| DTC C2227 | Excessive temperature of brake disc |
| DTC C2380 | ABS-ESC valve error |
| DTC C2402 | Motor electrical |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.