SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2024WAGONEER L SERIES II, RWDREPAIR AND DIAGNOSISACCESSORIES & EQUIPMENTINTERIOR/ILLUMINATION LIGHTS(AMBIENT LIGHT MODULE (ALM) - ELECTRICAL DIAGNOSTICS)DTC TROUBLESHOOTINGU1009-00 LIN 2 BUSDIAGNOSTIC TEST
2024 Jeep Wagoneer L Series II, RWD

Diagnostic Test

2024 Jeep Wagoneer L Series II, RWDSECTION Diagnostic Test
  1. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECU's) and record on the repair order.
    2. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 10.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read ALM DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

  2. ISOLATE AND CHECK THE (D832) LIN BUS 2 CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT IN THE ALM HARNESS 
    1. The ignition must be off when performing a resistance check to find a short between circuits.
    2. Isolate the circuit by disconnecting the Electronic Control Unit (ECU) and every component harness connector containing the circuit being tested. At this time leave all in-line connectors connected. Note:  Use the wiring diagram as a guide to follow the path of the circuit.
    3. Connect one lead of the DVOM to the circuit being tested at the ECU harness connector.
    4. With the other lead of the DVOM probe all other circuits at the ECU harness connector.
      NOTE:

      With the circuit isolated there should be no continuity between the circuit being tested and any other circuit.

      Is there continuity between the circuit being tested and any other circuit?

      Yes 

      • Repair the short between the circuits that have continuity. Use the wiring diagram as a guide to trace the circuits and look for any in-line connectors to help isolate the location of the short.
      • Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .

      No 

      • Go To  3
  3. ISOLATE AND CHECK THE (D832) LIN 2 BUS CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. The ignition must be off when checking the continuity of a circuit.
    2. Isolate the circuit by disconnecting the Electronic Control Unit (ECU) and the component harness connector containing the circuit being tested. Note:  Use the wiring diagram as a guide to follow the path of the circuit.
    3. Before measuring the resistance of any circuit, first measure the resistance between the two leads of the DVOM. Note:  The meter leads can add resistance to the measurement value.
    4. Connect one lead of the DVOM to the circuit being tested at the incorrect color Light Pipe harness connector.
    5. Connect the other lead to the circuit being tested at the ECU harness connector and measure the resistance of the circuit.

      Is the resistance below 3.0 Ohms?

      Yes 

      • Go To  4

      No 

      • Repair the circuit for an open or high resistance.
      • Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .
  4. CHECK RELATED ALM AND COMPONENT CONNECTIONS 
    1. Disconnect all ALM harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Perform a terminal drag test on each connector terminal to verify proper terminal tension.

      Repair any conditions that are found.

    5. Reconnect all ALM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    10. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      No 

      • The wiring or poor connection has been repaired.
      • Perform the BODY VERIFICATION TEST. Refer to: BODY VERIFICATION TEST .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.