Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2023RENEGADE TRAILHAWKREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCOLLISION/AVOIDANCE(LEFT BLIND SPOT SENSOR MODULE (LBSS) (BSM) - ELECTRICAL DIAGNOSTICS)
2023 Jeep Renegade Trailhawk
(Left Blind Spot Sensor Module (LBSS) (BSM) - Electrical Diagnostics)
2023 Jeep Renegade TrailhawkSECTION (Left Blind Spot Sensor Module (LBSS) (BSM) - Electrical Diagnostics)
- Diagnostic Code Index
- DTC Troubleshooting
- C1000-44-Electronic Control Unit-Data Memory Failure
- C1000-45-Electronic Control Unit-Program Memory Failure
- C1000-46-Electronic Control Unit-Calibration-Parameter Memory Failure
- C1000-47-Electronic Control Unit-Watchdog-Safety Failure
- C1002-02-LBSS Radar Sensor Address Fault-General Signal Failure
- C1003-04-Blind Spot Sensor Problem-System Internal Failures
- C1003-49-Blind Spot Sensor Problem-Internal Electronic Failure
- C1003-97-Blind Spot Sensor Problem-Component Or System Operation Obstructed Or Blocked
- C1004-16-Battery Voltage Input Circuit-Circuit Voltage Below Threshold
- C1004-17-Battery Voltage Input Circuit-Circuit Voltage Above Threshold
- C1006-64-Status_BH_BCM2.TURNINDICATIONSTS (From Body Control Module) - Signal Plausibility Failure
- C1008-64-Vehicle Configuration Mismatch - Signal Plausibility Failure
- C100B-11-Left Blind Spot Sensor-Circuit Short To Ground
- C100B-15-Left Blind Spot Sensor-Circuit Short To Battery Or Open
- C100B-4B-Left Blind Spot Sensor-Over Temperature
- C2000-64-Status-TTM.TRAILERGENERICFAILSTS-Signal Plausibility Failure
- C2001-64-Status-BH-BCM1.PARKBRAKESTS-Signal Plausibility Failure
- C2002-64-Status-CCAN5.SHIFTLEVERPOSITION-Signal Plausibility Failure
- U0010-87-B Can-Missing Message
- U0010-88-B Can-Bus Off
- U146D-64-LBSS OPERATIONALMODESTS-Signal Plausibility Failure
- U148D-64-IPC-Vehicle-Setup.BSDENABLE-Signal Plausibility Failure
- U149D-64-Status-CCAN3.VEHICLESPEEDVSOSIGFAILSTS-Signal Plausibility Failure
- U1700-86-Body Computer Module (BCM)-Signal Invalid
- U1700-87-Body Computer Module (BCM)-Missing Message
- U1703-86-Instrument Panel Cluster (IPC)-Signal Invalid
- U1703-87-Instrument Panel Cluster (IPC)-Missing Message
- U1752-86-Right Blind Spot Sensor (RBSS)-Signal Invalid
- U1752-87-Right Blind Spot Sensor (RBSS)-Missing Message
- U1763-86-TTM (Trailer Tow Module)-Signal Invalid
- U1763-87-TTM (Trailer Tow Module)-Missing Message
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.