Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2023RENEGADE LATITUDEREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEXDTC INDEX (1 OF 3)MODULE, FORWARD FACING CAMERA (FFCM)
2023 Jeep Renegade Latitude
Module, Forward Facing Camera (FFCM)
2023 Jeep Renegade LatitudeSECTION Module, Forward Facing Camera (FFCM)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| B1001-16 | POWER SUPPLY - CIRCUIT VOLTAGE BELOW THRESHOLD |
| B1001-17 | POWER SUPPLY - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| B1006-49 | HALF (HAPTIC LANE FEEDBACK) - INTERNAL ELECTRONIC FAILURE |
| B1007-54 | HALF (HAPTIC LANE FEEDBACK) - MISSING CALIBRATION |
| B2206-00 | CURRENT VIN MISMATCH - NO SUBTYPE INFORMATION |
| C0063-29 | YAW RATE SENSOR FROM BRAKE SYSTEM MODULE - SIGNAL SIGNAL INVALID |
| C0546-00 | VIN (VEHICLE IDENTIFICATION NUMBER) IMPLAUSIBLE OR INCOMPATIBLE FROM BODY CONTROL MODULE - NO SUBTYPE INFORMATION |
| C1003-29 | VEHICLE SPEED INFORMATION FROM BRAKE SYSTEM MODULE - SIGNAL - SIGNAL INVALID |
| C1401-64 | WHEEL SPEED PLAUSIBILITY FAILURE - SIGNAL PLAUSIBILITY FAILURE |
| C1401-86 | WHEEL SPEED PLAUSIBILITY FAILURE - SIGNAL INVALID |
| C1406-64 | BRAKE SWITCH PLAUSIBILITY - SIGNAL PLAUSIBILITY FAILURE |
| C1406-86 | BRAKE SWITCH PLAUSIBILITY - SIGNAL INVALID |
| C1407-86 | ACKNOWLEDGE SIGNAL FAIL FROM BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| C1408-86 | ESC (ELECTRONIC STABILITY CONTROL) FAIL STATUS PRESENT - SIGNAL INVALID |
| C1413-86 | EXTERNAL LIGHT SIGNAL FAULT - SIGNAL INVALID |
| C1413-87 | EXTERNAL LIGHT SIGNAL FAULT - MISSING MESSAGE |
| C1414-87 | LOST COMMUNICATION WITH BCM (CAN MESSAGE C1_IGW2 MISSING FROM BODY CONTROL MODULE) - MISSING MESSAGE |
| C1433-86 | EXTERNAL BRAKE SIGNAL FAILURE FROM BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| C1434-94 | BRAKE JERK REQUEST NOT PLAUSIBLE - UNEXPECTED OPERATION |
| C143A-86 | TRAILER TOW MODULE STOP LIGHT SIGNAL FROM TTM (TRAILER TOW MODULE) FAIL - SIGNAL INVALID |
| C14A5-68 | SENSOR BLINDED - EVENT INFORMATION |
| C14A5-97 | SENSOR BLINDED - COMPONENT OR SYSTEM OPERATION OBSTRUCTED OR BLOCKED |
| C14AA-64 | SENSOR ADJUSTMENT REQUIRED - SIGNAL PLAUSIBILITY FAILURE |
| C2210-4B | ECU OVERTEMPERATURE - OVER TEMPERATURE |
| U0001-88 | C3 CAN BUS (PRIVATE) - BUS OFF |
| U0055-00 | CAN C2 BUS-NO SUBTYPE INFORMATION |
| U0056-00 | CAN C2 BUS OFF PERFORMANCE-NO SUBTYPE INFORMATION |
| U0100-00 | LOSS OF COMMUNICATION WITH ENGINE CONTROL MODULE-ECM-NO SUBTYPE INFORMATION |
| U0100-87 | LOST COMMUNICATION WITH ENGINE CONTROL MODULE (ECM) - MISSING MESSAGE |
| U0101-87 | C2 CAN BUS-MISSING MESSAGE |
| U0101-88 | C2 CAN BUS-BUS OFF |
| U0121-00 | LOSS OF COMMUNICATION WITH BRAKE SYSTEM MODULE-BSM-NO SUBTYPE INFORMATION |
| U0121-87 | LOSS OF COMMUNICATION WITH BRAKE SYSTEM MODULE (BSM) - MISSING MESSAGE |
| U0121-8F | LOSS OF COMMUNICATION WITH BRAKE SYSTEM MODULE (BSM) - ERRATIC |
| U0131-00 | LOSS OF COMMUNICATION WITH ELECTRIC POWER STEERING-EPS-NO SUBTYPE INFORMATION |
| U0140-00 | LOSS OF COMMUNICATION WITH BODY CONTROL MODULE-BCM-NO SUBTYPE INFORMATION |
| U0140-87 | LOSS OF COMMUNICATION WITH BODY CONTROL MODULE (BCM) - MISSING MESSAGE |
| U0140-8F | LOSS OF COMMUNICATION WITH BODY CONTROL MODULE (BCM) - ERRATIC |
| U0155-00 | LOSS OF COMMUNICATION WITH INSTRUMENT PANEL CLUSTER-IPC-NO SUBTYPE INFORMATION |
| U0401-29 | IMPLAUSIBLE DATA RECEIVED FROM ENGINE CONTROL MODULE (ECM) - SIGNAL - SIGNAL INVALID |
| U0401-64 | IMPLAUSIBLE DATA RECEIVED FROM ENGINE CONTROL MODULE (ECM) - SIGNAL PLAUSIBILITY FAILURE |
| U0415-00 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE-BSM-NO SUBTYPE INFORMATION |
| U0420-00 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING-EPS-NO SUBTYPE INFORMATION |
| U0420-29 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING (EPS) - SIGNAL - SIGNAL INVALID |
| U0422-00 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE BCM-NO SUBTYPE INFORMATION |
| U0422-29 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE - SIGNAL - SIGNAL INVALID |
| U1415-00 | IMPLAUSIBLE/MISSING VEHICLE CONFIGURATION DATA - NO SUBTYPE INFORMATION |
| U1700-86 | BODY CONTROL MODULE (BCM) - SIGNAL INVALID |
| U1700-87 | BODY CONTROL MODULE (BCM) - MISSING MESSAGE |
| U1701-87 | ENGINE CONTROL MODULE (ECM) - MISSING MESSAGE |
| U1702-29 | ELECTRIC POWER STEERING (EPS) - SIGNAL - SIGNAL INVALID |
| U1702-64 | ELECTRIC POWER STEERING (EPS) - SIGNAL PLAUSIBILITY FAILURE |
| U1702-86 | ELECTRIC POWER STEERING (EPS) - SIGNAL INVALID |
| U1702-87 | ELECTRIC POWER STEERING (EPS) - MISSING MESSAGE |
| U1706-86 | BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| U1706-87 | BRAKE SYSTEM MODULE (BSM) - MISSING MESSAGE |
| U1930-86 | HALF OPERATIONAL MODE STATUS-SIGNAL INVALID |
| U1931-86 | HALF (HAPTIC LANE FEEDBACK) OPERATIONAL MODE STATUS - SIGNAL INVALID |
| U1932-86 | IGNITION WORKING CONDITION SIGNAL FROM BODY CONTROL MODULE - SIGNAL INVALID |
| U1933-87 | BCM-COMMAND FROM BODY CONTROL MODULE-BCM-MISSING MESSAGE |
| U1934-87 | BCM-COMMAND- FROM BCM-AND BODY2- FROM BCM-MISSING MESSAGE |
| U1950-83 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE (CAN MESSAGE BCM_COMMAND INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1952-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BRAKE1 INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1958-83 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE (CAN MESSAGE BSM_YRS_DATA INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U195E-83 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING (CAN MESSAGE EPS_TORQUE_OVERLAY INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1966-83 | IMPLAUSIBLE DATA RECEIVED FROM ELECTRIC POWER STEERING (CAN MESSAGE GE INTEGRITY ERROR) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.