Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2023RENEGADE LATITUDEREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCOLLISION/AVOIDANCEACTIVE CRUISE CONTROL (ACC) MODULE - DTCS C1200-16 TO C1436-86
2023 Jeep Renegade Latitude
Active Cruise Control (Acc) Module - DTCS C1200-16 To C1436-86
2023 Jeep Renegade LatitudeSECTION Active Cruise Control (Acc) Module - DTCS C1200-16 To C1436-86
- DTC Troubleshooting
- C1200-16-Battery Voltage - Circuit Voltage Below Threshold
- C1200-17-Battery Voltage - Circuit Voltage Above Threshold
- C1400-86-Master Cylinder Pressure Fault - Signal Invalid
- C1401-86-Wheel Speed Plausibility Failure - Signal Invalid
- C1402-86-Multi Axis Acceleration Sensors From BSM Failure - Signal Invalid
- C1403-86-Electrical Power Steering Failure - Signal Invalid
- C1404-86-Engine Signal Failure - Signal Invalid
- C1405-86-Trailer Tow Module Fail - Signal Invalid
- C1406-86-Brake Switch Plausibility - Signal Invalid
- C1407-86-Implausible Data Received From BSM (Invalid Acknowledge Can Bus Signal From Brake System Module) - Signal Invalid
- C1408-86-ESC (Electronic Stability Control) Fail Status Present - Signal Invalid
- C1409-97-Radar Sensor Blind - Component Or System Operation Obstructed Or Blocked
- C140A-55-Vehicle EOL Configuration - Not Configured
- C140B-05-Vehicle Configuration (PROXI Configuration) Not Learned/Mismatch - System Programming Failures
- C140C-86-DASM (Driver Assistant System Module) Intervention Request Time Out Of Range - Signal Invalid
- C140D-86-Seat Belt Information Failure - Signal Invalid
- C140E-05-Adaptive Cruise Control EOL Activation Fault - System Programming Failure
- C140E-86-External Temperature Signal From BCM-Body Control Module-Signal Invalid
- C140F-05-Adaptive Cruise Control EOL Configuration Fault - System Programming Failure
- C1410-87-Lost Communication With BCM (Can Message C2_IGW1 Missing From Body Control Module) - Missing Message
- C1411-49-Control Unit - Internal Electronic Failure
- C1411-96-Control Unit-Component Internal Failure
- C1412-54-Calibration Procedure - Missing Calibration
- C1413-86-External Light Message - Signal Invalid
- C1413-87-External Light Message - Missing Message
- C1414-87-Lost Communication With IPC (Can Message Cluster2 Missing From Instrument Panel Cluster) - Missing Message
- C1415-53-Manufacturing Mode-Deactivated
- C1416-87-VIN Message - Missing Message
- C1417-78-Horizontal Misalignment Sensor - Alignment Or Adjustment Incorrect
- C1418-78-Vertical Misalignment Sensor - Alignment Or Adjustment Incorrect
- C1419-64-Internal Wheel Speed Plausibility Failure - Signal Plausibility Failure
- C141A-64-Internal Steering Wheel Angle Plausibility Failure - Signal Plausibility Failure
- C141B-97-Video Camera Blind - Component Or System Operation Obstructed Or Blocked
- C141C-08-Video Camera Private Can Communication Failure-Bus Signal Message Failure
- C141C-82-Video Camera Private Can Communication Failure-Alive Sequence Counter Incorrect Not Updated
- C141C-86-Video Camera Private Can Communication Failure - Signal Invalid
- C141C-87-Video Camera Private Can Communication Failure-Missing Message
- C141C-88-Video Camera Private Can Communication Failure-Bus Off
- C141D-47-Ecu Internal Performance (Ecu Microcontroller Internal Reset) - Watchdog Safety MICROCONTROL Failure
- C141E-49-Component Internal Communication Failure - Internal Electronic Failure
- C141F-96-Hardware Reset Failure - Component Internal Failure
- C1420-25-Radar Sensor Blinded (Signal Disturbed) - Signal Shape Waveform Failure
- C1420-66-Radar Sensor Blinded (Signal Disturbed) - Signal Has Too Many Transitions Events
- C1421-64-Internal Multi Axis Acceleration Plausibility Failure - Signal Plausibility Failure
- C1422-49-Internal Hardware Plausibility Check - Internal Electronic Failure
- C1422-66-Internal Hardware Plausibility Check - Signal Has Too Many Transitions Events
- C1423-4B-Sensor Internal Temperature - Over Temperature
- C1424-4B-Component Internal Temperature - Over Temperature
- C1425-45-Flashed Software In Ecu Not Compatible - Program Memory Failure
- C1426-49-Control Unit Permanent Failure - Internal Electronic Failure
- C1427-66-Radar Sensor Blinded (Radar Modulation Disturbed) - Signal Has Too Many Transitions Events
- C1427-68-Radar Sensor Blinded (Radar Modulation Disturbed) - Event Information
- C1428-68-Sensor Blinded (Radar Unavailable) - Event Information
- C1429-66-Radar Hardware OVERTEMPERATURE - Signal Has Too Many Transitions Events
- C1429-68-Radar Hardware OVERTEMPERATURE - Event Information
- C1430-86-VIN Plausibility Check Failure - Signal Invalid
- C1431-86-Yaw Rate Acceleration Sensor From BSM Failure - Signal Invalid
- C1432-86-Turn Indicator Signal Failure From BCM - Signal Invalid
- C1433-86-External Brake Signal Failure From BSM - Signal Invalid
- C1434-86-Brake Jerk Request Not Plausible - Signal Invalid
- C1435-87-Status EPB Message From BSM (Brake System Module) Absent - Missing Message
- C1436-86-Electric Parking Brake System Fail - Signal Invalid
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.