Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2023RENEGADE LATITUDEREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCOLLISION/AVOIDANCE(FORWARD FACING CAMERA MODULE (FFCM) - ELECTRICAL DIAGNOSTICS)
2023 Jeep Renegade Latitude
(Forward Facing Camera Module (FFCM) - Electrical Diagnostics)
2023 Jeep Renegade LatitudeSECTION (Forward Facing Camera Module (FFCM) - Electrical Diagnostics)
- Diagnostic Code Index
- DTC Troubleshooting
- B1001-16-Power Supply - Circuit Voltage Below Threshold
- B1001-17-Power Supply - Circuit Voltage Above Threshold
- B1006-49-Half (Haptic Lane Feedback) - Internal Electronic Failure
- B1007-54-Half (Haptic Lane Feedback) - Missing Calibration
- B2206-00-Current VIN Mismatch - No Subtype Information
- C0063-29-Yaw Rate Sensor From Brake System Module - Signal Invalid
- C0546-00-VIN (Vehicle Identification Number) Implausible Or Incompatible From Body Control Module - No Subtype Information
- C1003-29-Vehicle Speed Information From Brake System Module - Signal - Signal Invalid
- C1401-64-Wheel Speed Plausibility Failure - Signal Plausibility Failure
- C1401-86-Wheel Speed Plausibility Failure - Signal Invalid
- C1406-64-Brake Switch Plausibility - Signal Plausibility Failure
- C1406-86-Brake Switch Plausibility - Signal Invalid
- C1407-86-Acknowledge Signal Fail From Brake System Module (BSM) - Signal Invalid
- C1408-86-ESC (Electronic Stability Control) Fail Status Present - Signal Invalid
- C1413-86-External Light Signal Fault - Signal Invalid
- C1413-87-External Light Signal Fault - Missing Message
- C1414-87-Lost Communication With BCM (Can Message C1_IGW2 Missing From Body Control Module) - Missing Message
- C1433-86-External Brake Signal Failure From Brake System Module (BSM) - Signal Invalid
- C1434-94-Brake Jerk Request Not Plausible - Unexpected Operation
- C143A-86-Trailer Tow Module Stop Light Signal From TTM (Trailer Tow Module) Fail - Signal Invalid
- C14A5-68-Sensor Blinded - Event Information
- C14A5-97-Sensor Blinded - Component Or System Operation Obstructed Or Blocked
- C14AA-64-Sensor Adjustment Required - Signal Plausibility Failure
- C2210-4B-Ecu OVERTEMPERATURE - Over Temperature
- U0001-88-C3 Can Bus (Private) - Bus Off
- U0055-00-Can C2 Bus-No Subtype Information
- U0056-00-Can C2 Bus Off Performance-No Subtype Information
- U0100-00-Loss Of Communication With Engine Control Module-ECM-No Subtype Information
- U0100-87-Lost Communication With Engine Control Module (ECM) - Missing Message
- U0101-87-C2 Can Bus-Missing Message
- U0101-88-C2 Can Bus-Bus Off
- U0121-00-Loss Of Communication With Brake System Module-BSM-No Subtype Information
- U0121-87-Loss Of Communication With Brake System Module (BSM) - Missing Message
- U0121-8F-Loss Of Communication With Brake System Module (BSM) - Erratic
- U0131-00-Loss Of Communication With Electric Power Steering-EPS-No Subtype Information
- U0140-00-Loss Of Communication With Body Control Module-BCM-No Subtype Information
- U0140-87-Loss Of Communication With Body Control Module (BCM) - Missing Message
- U0140-8F-Loss Of Communication With Body Control Module (BCM) - Erratic
- U0155-00-Loss Of Communication With Instrument Panel Cluster-IPC-No Subtype Information
- U0401-29-Implausible Data Received From Engine Control Module (ECM) - Signal - Signal Invalid
- U0401-64-Implausible Data Received From Engine Control Module (ECM) - Signal Plausibility Failure
- U0415-00-Implausible Data Received From Brake System Module-BSM-No Subtype Information
- U0420-00-Implausible Data Received From Electric Power Steering-EPS-No Subtype Information
- U0420-29-Implausible Data Received From Electric Power Steering (EPS) - Signal - Signal Invalid
- U0422-00-Implausible Data Received From Body Control Module BCM-No Subtype Information
- U0422-29-Implausible Data Received From Body Control Module - Signal - Signal Invalid
- U1415-00-Implausible/Missing Vehicle Configuration Data - No Subtype Information
- U1700-86-Body Control Module (BCM) - Signal Invalid
- U1700-87-Body Control Module (BCM) - Missing Message
- U1701-87-Engine Control Module (ECM) - Missing Message
- U1702-29-Electric Power Steering (EPS) - Signal - Signal Invalid
- U1702-64-Electric Power Steering (EPS) - Signal Plausibility Failure
- U1702-86-Electric Power Steering (EPS) - Signal Invalid
- U1702-87-Electric Power Steering (EPS) - Missing Message
- U1706-86-Brake System Module (BSM) - Signal Invalid
- U1706-87-Brake System Module (BSM) - Missing Message
- U1930-86-Half Operational Mode Status-Signal Invalid
- U1931-86-Half (Haptic Lane Feedback) Operational Mode Status - Signal Invalid
- U1932-86-Ignition Working Condition Signal From Body Control Module - Signal Invalid
- U1933-87-BCM-Command From Body Control Module-BCM-Missing Message
- U1934-87-BCM-Command- From BCM-And Body2- From BCM-Missing Message
- U1950-83-Implausible Data Received From Body Control Module (Can Message BCM_Command Integrity Error) - Value Of Signal Protection Calculation Incorrect
- U1952-83-Implausible Data Received From Brake System Module (Can Message Brake1 Integrity Error) - Value Of Signal Protection Calculation Incorrect
- U1958-83-Implausible Data Received From Brake System Module (Can Message BSM_Yrs_Data Integrity Error) - Value Of Signal Protection Calculation Incorrect
- U195E-83-Implausible Data Received From Electric Power Steering (Can Message EPS_Torque_Overlay Integrity Error) - Value Of Signal Protection Calculation Incorrect
- U1966-83-Implausible Data Received From Electric Power Steering (Can Message GE Integrity Error) - Value Of Signal Protection Calculation Incorrect
- Standard Procedure
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.