Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2023GLADIATOR MOJAVE, PART TIME T/CASE CONTROL, AUTOMATIC TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCOMMUNICATION DEVICESBODY CONTROL MODULE (BCM) - DTCS B163E-15 TO B16E7-15DTC TROUBLESHOOTINGB168E-11-FRONT FOG LAMP SWITCH-CIRCUIT SHORT TO GROUNDDIAGNOSTIC TEST
2023 Jeep Gladiator Mojave, Part Time T/Case Control, Automatic Trans
Diagnostic Test
2023 Jeep Gladiator Mojave, Part Time T/Case Control, Automatic TransSECTION Diagnostic Test
- READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
- With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
- With the scan tool, run a vehicle Scan Report, or record the Environmental Data related to the DTCs.
- With the scan tool, erase all DTCs.
- Turn the ignition off for a minimum of 10.0 seconds.
- Turn the ignition on.
- Using the recorded Environmental Data and the When Monitored Conditions above, operate the vehicle in the conditions that set the DTC.
- With the scan tool, read Body Control Module (BCM) DTCs.
Did the DTC return?
Yes
- Go To 2
No
- Perform the appropriate INTERMITTENT CONDITION diagnostic procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
- DISCONNECT THE HEADLAMP SWITCH HARNESS CONNECTOR - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
- Turn the ignition off.
- Disconnect the component harness connector(s) containing the circuit being tested. Note: Use the wiring diagram as a guide to follow the path of the circuit.
- With the scan tool, erase all DTCs.
- Turn the ignition off for a minimum of 10.0 seconds.
- Turn the ignition on.
- Using the recorded Environmental Data and the When Monitored Conditions above, operate the vehicle in the conditions that set the DTC.
- With the scan tool, read BCM DTCs.
Did the DTC return?
Yes
- Go To 3
No
- Replace the Headlamp Switch in accordance with the Service Information. Refer to SWITCH, HEADLAMP, REMOVAL AND INSTALLATION .
- Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
- DISCONNECT THE BCM HARNESS CONNECTOR(S) AND CHECK THE (L116) HEADLAMP/FOG LAMP SWITCH SIGNAL CIRCUIT FOR A SHORT TO GROUND
- The ignition must be off when checking a circuit for continuity to ground.
- Disconnect all Electronic Control Unit (ECU) harness connectors containing the circuit being tested. Note: Use the wiring diagram as a guide to follow the path of the circuit.
- Connect the negative lead of the DVOM to a known good ground.
- Connect the positive lead of the DVOM to the circuit being tested at the ECU or component harness connector and check for continuity between the circuit and ground.
NOTE:When probing a circuit at any harness connector, always use an appropriate probing tool to prevent any possible damage to the harness connector terminals.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.