Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2023COMPASS LATITUDEREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX (1 OF 2)MODULE, ANTILOCK BRAKE (ABS), CONTINENTAL
2023 Jeep Compass Latitude
Module, Antilock Brake (Abs), Continental
2023 Jeep Compass LatitudeSECTION Module, Antilock Brake (Abs), Continental
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| C0020-01 | ABS PUMP MOTOR CONTROL - GENERAL ELECTRICAL FAILURE |
| C0020-16 | ABS PUMP MOTOR CONTROL - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C0020-1C | ABS PUMP MOTOR CONTROL - CIRCUIT VOLTAGE OUT OF RANGE |
| C0020-35 | ABS PUMP MOTOR CONTROL - SIGNAL HIGH TIME>MAXIMUM |
| C0021-02 | BRAKE BOOSTER - GENERAL SIGNAL FAILURE |
| C0030-02 | LEFT FRONT TONE WHEEL - GENERAL SIGNAL FAILURE |
| C0031-1D | LEFT FRONT WHEEL SPEED SENSOR - CIRCUIT CURRENT OUT OF RANGE |
| C0031-2F | LEFT FRONT WHEEL SPEED SENSOR - SIGNAL ERRATIC |
| C0031-4A | LEFT FRONT WHEEL SPEED SENSOR - INCORRECT COMPONENT INSTALLED |
| C0031-62 | LEFT FRONT WHEEL SPEED SENSOR - SIGNAL COMPARE FAILURE |
| C0033-02 | RIGHT FRONT TONE WHEEL - GENERAL SIGNAL FAILURE |
| C0034-1D | RIGHT FRONT WHEEL SPEED SENSOR - CIRCUIT CURRENT OUT OF RANGE |
| C0034-2F | RIGHT FRONT WHEEL SPEED SENSOR - SIGNAL ERRATIC |
| C0034-4A | RIGHT FRONT WHEEL SPEED SENSOR - INCORRECT COMPONENT INSTALLED |
| C0034-62 | RIGHT FRONT WHEEL SPEED SENSOR - SIGNAL COMPARE FAILURE |
| C0036-02 | LEFT REAR TONE WHEEL - GENERAL SIGNAL FAILURE |
| C0037-1D | LEFT REAR WHEEL SPEED SENSOR - CIRCUIT CURRENT OUT OF RANGE |
| C0037-2F | LEFT REAR WHEEL SPEED SENSOR - SIGNAL ERRATIC |
| C0037-4A | LEFT REAR WHEEL SPEED SENSOR - INCORRECT COMPONENT INSTALLED |
| C0037-62 | LEFT REAR WHEEL SPEED SENSOR - SIGNAL COMPARE FAILURE |
| C0039-02 | RIGHT REAR TONE WHEEL - GENERAL SIGNAL FAILURE |
| C003A-1D | RIGHT REAR WHEEL SPEED SENSOR - CIRCUIT CURRENT OUT OF RANGE |
| C003A-2F | RIGHT REAR WHEEL SPEED SENSOR - SIGNAL ERRATIC |
| C003A-4A | RIGHT REAR WHEEL SPEED SENSOR - INCORRECT COMPONENT INSTALLED |
| C003A-62 | RIGHT REAR WHEEL SPEED SENSOR - SIGNAL COMPARE FAILURE |
| C0040-29 | BRAKE PEDAL SWITCH - SIGNAL INVALID |
| C0040-2A | BRAKE PEDAL SWITCH - STUCK |
| C0040-62 | BRAKE PEDAL SWITCH - SIGNAL COMPARE FAILURE |
| C0044-01 | BRAKE PRESSURE SENSOR 1 - GENERAL ELECTRICAL FAILURE |
| C0044-28 | BRAKE PRESSURE SENSOR 1 - SIGNAL BIAS LEVEL OUT OF RANGE / ZERO ADJUSTMENT FAILURE |
| C0044-49 | BRAKE PRESSURE 1 - INTERNAL ELECTRONIC FAILURE |
| C0044-62 | BRAKE PRESSURE SENSOR 1 - SIGNAL COMPARE FAILURE |
| C0044-64 | BRAKE PRESSURE SENSOR 1 - SIGNAL PLAUSIBILITY FAILURE |
| C0051-22 | STEERING WHEEL POSITION SENSOR - SIGNAL AMPLITUDE > MAXIMUM |
| C0051-28 | STEERING WHEEL POSITION SENSOR - SIGNAL BIAS LEVEL OUT OF RANGE / ZERO ADJUSTMENT FAILURE |
| C0051-49 | STEERING WHEEL POSITION SENSOR - INTERNAL ELECTRONIC FAILURE |
| C0051-54 | STEERING WHEEL POSITION SENSOR - MISSING CALIBRATION |
| C0051-62 | STEERING WHEEL POSITION SENSOR - SIGNAL COMPARE FAILURE |
| C006A-28 | MULTI-AXIS ACCELERATION SENSOR - SIGNAL BIAS LEVEL OUT OF RANGE / ZERO ADJUSTMENT FAILURE |
| C006A-49 | MULTI-AXIS ACCELERATION SENSOR - INTERNAL ELECTRONIC FAILURE |
| C006A-54 | MULTI-AXIS ACCELERATION SENSOR - MISSING CALIBRATION |
| C006A-62 | MULTI-AXIS ACCELERATION SENSOR - SIGNAL COMPARE FAILURE |
| C006A-78 | MULTI-AXIS ACCELERATION SENSOR - ALIGNMENT OR ADJUSTMENT INCORRECT |
| C0078-86 | TIRE DIAMETER - SIGNAL INVALID |
| C1046-92 | LEFT FRONT WHEEL PRESSURE PHASE MONITORING - PERFORMANCE OR INCORRECT OPERATION |
| C1047-92 | RIGHT FRONT WHEEL PRESSURE PHASE MONITORING - PERFORMANCE OR INCORRECT OPERATION |
| C1048-92 | LEFT REAR WHEEL PRESSURE PHASE MONITORING - PERFORMANCE OR INCORRECT OPERATION |
| C1049-92 | RIGHT REAR WHEEL PRESSURE PHASE MONITORING - PERFORMANCE OR INCORRECT OPERATION |
| C1082-01 | VACUUM PRESSURE SENSOR - GENERAL ELECTRICAL FAILURE |
| C1082-02 | VACUUM PRESSURE SENSOR - GENERAL SIGNAL FAILURE |
| C1082-2F | VACUUM PRESSURE SENSOR - SIGNAL ERRATIC |
| C10CD-01 | ELECTRONIC PARK BRAKE SWITCH - GENERAL ELECTRICAL FAILURE |
| C10CD-2A | ELECTRONIC PARK BRAKE SWITCH - STUCK |
| C10D0-48 | ELECTRONIC PARK BRAKE MODULE - SUPERVISION SOFTWARE FAILURE |
| C10D0-4B | ELECTRONIC PARK BRAKE MODULE - OVER TEMPERATURE |
| C10D0-52 | ELECTRONIC PARK BRAKE MODULE - NOT ACTIVATED |
| C10D0-53 | ELECTRONIC PARK BRAKE MODULE - DEACTIVATED |
| C10D0-92 | ELECTRONIC PARK BRAKE MODULE - PERFORMANCE OR INCORRECT OPERATION |
| C10D0-9A | ELECTRONIC PARK BRAKE MODULE - COMPONENT OR SYSTEM OPERATING CONDITIONS |
| C10EA-00 | LEFT PARK BRAKE ACTUATOR |
| C10EA-01 | LEFT PARK BRAKE ACTUATOR - GENERAL ELECTRICAL FAILURE |
| C10EA-04 | LEFT PARK BRAKE ACTUATOR - SYSTEM INTERNAL FAILURE |
| C10EB-00 | RIGHT PARK BRAKE ACTUATOR |
| C10EB-01 | RIGHT PARK BRAKE ACTUATOR - GENERAL ELECTRICAL FAILURE |
| C10EB-04 | RIGHT PARK BRAKE ACTUATOR - SYSTEM INTERNAL FAILURE |
| C10EC-00 | PARK BRAKE ACTUATOR CORRELATION |
| C10ED-00 | ELECTRONIC PARK BRAKE SWITCH LED |
| C121A-09 | STEERING ANGLE SENSOR NOT INITIALIZED - COMPONENT FAILURES |
| C121C-00 | TORQUE REQUEST SIGNAL DENIED |
| C1239-00 | EMISSION ROLLS TEST ACTIVE |
| C123B-4B | ESP SYSTEM CONTROL TOO LONG - OVER TEMPERATURE |
| C1246-1C | VACUUM PRESSURE SENSOR SUPPLY - CIRCUIT VOLTAGE OUT OF RANGE |
| C124F-00 | ESP REQUEST DENIED FROM ACC |
| C1260-00 | ABS/ESC DYNAMIC CONTROLS DISABLED |
| C15E9-00 | DYNAMIC STEERING TORQUE REQUEST DENIED |
| C2100-16 | BATTERY VOLTAGE LOW - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C2100-9A | BATTERY VOLTAGE LOW - COMPONENT OR SYSTEM OPERATING CONDITIONS |
| C2101-17 | BATTERY VOLTAGE HIGH - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C2101-9A | BATTERY VOLTAGE HIGH - COMPONENT OR SYSTEM OPERATING CONDITIONS |
| C212A-16 | SYSTEM VOLTAGE LOW - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C212A-17 | SYSTEM VOLTAGE HIGH - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C2200-41 | ANTI-LOCK BRAKE MODULE INTERNAL - GENERAL CHECKSUM FAILURE |
| C2200-44 | ANTI-LOCK BRAKE MODULE INTERNAL - DATA MEMORY FAILURE |
| C2200-45 | ANTI-LOCK BRAKE MODULE INTERNAL - PROGRAM MEMORY FAILURE |
| C2200-46 | ANTI-LOCK BRAKE MODULE INTERNAL - CALIBRATION / PARAMETER MEMORY FAILURE |
| C2200-47 | ANTI-LOCK BRAKE MODULE INTERNAL - WATCHDOG / SAFETY AuC FAILURE |
| C2200-48 | ANTI-LOCK BRAKE MODULE INTERNAL - SUPERVISION SOFTWARE FAILURE |
| C2200-49 | ANTI-LOCK BRAKE MODULE INTERNAL - INTERNAL ELECTRONIC FAILURE |
| C2202-00 | ORIGINAL VIN MISMATCH / MISSING |
| C2206-00 | VEHICLE CONFIGURATION MISMATCH |
| C220B-00 | ABS ACC VALVES NOT CALIBERATED |
| C2212-00 | ECU IN - PLANT MODE |
| C2222-68 | IMPROPER POWERDOWN - EVENT INFORMATION |
| C2312-2A | ESP OFF SWITCH - STUCK |
| P1DCB-72 | REVERSE GEAR SWITCH - ACTUATOR STUCK OPEN |
| U0002-00 | CAN C BUS OFF PERFORMANCE |
| U0056-00 | CAN CH BUS OFF PERFORMANCE |
| U0100-00 | LOST COMMUNICATION WITH ECM/PCM |
| U0101-00 | LOST COMMUNICATION WITH TCM |
| U0102-00 | LOST COMMUNICATION WITH TRANSFER CASE CONTROL MODULE / AWD |
| U0104-00 | LOST COMMUNICATION WITH CRUISE CONTROL MODULE |
| U0125-00 | LOST COMMUNICATION WITH MULTI-AXIS ACCELERATION SENSOR |
| U0131-00 | LOST COMMUNICATION WITH ELECTRIC POWER STEERING CONTROL MODULE |
| U0140-00 | LOST COMMUNICATION WITH BODY CONTROL MODULE |
| U0151-00 | LOST COMMUNICATION WITH OCCUPANT RESTRAINT CONTROLLER (ORC) |
| U0401-00 | INVALID DATA RECEIVED FROM ECM PCM A |
| U0402-00 | INVALID DATA RECEIVED FROM TCM |
| U0403-00 | IMPLAUSIBLE DATA RECEIVED FROM TCASE |
| U0405-00 | INVALID DATA RECEIVED FROM CRUISE CONTROL MODULE |
| U0420-00 | INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULE |
| U0422-00 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE |
| U0432-00 | INVALID DATA RECEIVED FROM MULTI-AXIS ACCELERATION SENSOR MODULE |
| U0452-00 | IMPLAUSIBLE DATA RECEIVED FROM RESTRAINTS CONTROL MODULE |
| U140E-00 | IMPLAUSIBLE VEHICLE CONFIGURATION DATA RECEIVED |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.