Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2013WRANGLER SPORT, AUTOMATIC TRANSREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 161 (DTC INDEX)MODULE, POWERTRAIN CONTROL (PCM), 62TE
2013 Jeep Wrangler Sport, Automatic Trans
Module, Powertrain Control (Pcm), 62TE
2013 Jeep Wrangler Sport, Automatic TransSECTION Module, Powertrain Control (Pcm), 62TE
WARNING: This page is about a different car, the 2014 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| P0218 | HIGH TEMPERATURE OPERATION ACTIVATED |
| P0562 | BATTERY/SYSTEM VOLTAGE LOW |
| P0602 | CONTROL MODULE PROGRAMMING ERROR/NOT PROGRAMMED |
| P0613 | INTERNAL TRANSMISSION PROCESSOR |
| P0706 | TRANSMISSION RANGE SENSOR RATIONALITY |
| P0711 | TRANSMISSION TEMPERATURE SENSOR PERFORMANCE |
| P0712 | TRANSMISSION TEMPERATURE SENSOR LOW |
| P0713 | TRANSMISSION TEMPERATURE SENSOR HIGH |
| P0714 | TRANSMISSION TEMPERATURE SENSOR INTERMITTENT |
| P0716 | INPUT SPEED SENSOR 1 CIRCUIT PERFORMANCE |
| P0721 | OUTPUT SPEED SENSOR CIRCUIT PERFORMANCE |
| P0729 | GEAR RATIO ERROR IN 6TH |
| P0731 | GEAR RATIO ERROR IN 1ST |
| P0732 | GEAR RATIO ERROR IN 2ND |
| P0733 | GEAR RATIO ERROR IN 3RD |
| P0734 | GEAR RATIO ERROR IN 4TH |
| P0735 | GEAR RATIO ERROR IN 5TH |
| P0736 | GEAR RATIO ERROR IN REVERSE |
| P0740 | TCC OUT OF RANGE |
| P0750 | L/R SOLENOID CIRCUIT |
| P0755 | 2/4 SOLENOID CIRCUIT |
| P075A | LC SOLENOID CIRCUIT |
| P0760 | OD SOLENOID CIRCUIT |
| P0765 | UD SOLENOID CIRCUIT |
| P076A | DC SOLENOID CIRCUIT |
| P0791 | TRANSFER SPEED SENSOR CIRCUIT |
| P0792 | COMPOUNDER SPEED RATIO ERROR |
| P083A | LC HYDRAULIC PRESSURE TEST |
| P083B | LC PRESSURE SWITCH RATIONALITY |
| P0841 | L/R PRESSURE SWITCH RATIONALITY |
| P0845 | 2/4 HYDRAULIC PRESSURE TEST |
| P0846 | 2/4 PRESSURE SWITCH RATIONALITY |
| P084A | DC HYDRAULIC PRESSURE TEST |
| P084B | DC PRESSURE SWITCH RATIONALITY |
| P0868 | LINE PRESSURE LOW |
| P0869 | LINE PRESSURE HIGH |
| P0870 | OD HYDRAULIC PRESSURE TEST |
| P0871 | OD PRESSURE SWITCH RATIONALITY |
| P0882 | TCM POWER INPUT LOW |
| P0883 | TCM POWER INPUT HIGH |
| P0884 | POWER UP AT SPEED |
| P0890 | SWITCHED BATTERY |
| P0933 | HYDRAULIC PRESSURE SENSOR RANGE/PERFORMANCE |
| P0934 | LINE PRESSURE SENSOR CIRCUIT LOW |
| P0935 | LINE PRESSURE SENSOR CIRCUIT HIGH |
| P0944 | LOSS OF HYDRAULIC PUMP PRIME |
| P0957 | AUTOSTICK CIRCUIT LOW |
| P0992 | 2/4/OD HYDRAULIC PRESSURE TEST |
| P1713 | RESTRICTED MANUAL VALVE IN T2 RANGE |
| P1741 | GEAR RATIO ERROR IN 4 PRIME |
| P1745 | TRANSMISSION LINE PRESSURE TOO HIGH FOR TOO LONG |
| P1771 | INADEQUATE ELEMENT VOLUME 2/4 |
| P1775 | SOLENOID SWITCH VALVE LATCHED IN TCC POSITION |
| P1790 | FAULT IMMEDIATELY AFTER SHIFT |
| P1794 | SPEED SENSOR GROUND ERROR |
| P1797 | MANUAL SHIFT OVERHEAT |
| P2700 | INADEQUATE ELEMENT VOLUME-LR |
| P2702 | INADEQUATE ELEMENT VOLUME FOR OD |
| P2703 | INADEQUATE ELEMENT VOLUME FOR UD |
| P273A | INADEQUATE ELEMENT VOLUME LC |
| P273B | INADEQUATE ELEMENT VOLUME DC |
| P2763 | TORQUE CONVERTER CLUTCH PRESSURE CONTROL CIRCUIT HIGH |
| P2764 | TORQUE CONVERTER CLUTCH PRESSURE CONTROL CIRCUIT LOW |
| U0002 | CAN C BUS OFF PERFORMANCE |
| U0100 | LOST COMMUNICATION WITH ECM/PCM |
| U0121 | LOST COMMUNICATION WITH ANTI-LOCK BRAKE MODULE |
| U0140 | LOST COMMUNICATION WITH BODY CONTROL MODULE |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.