Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2011WRANGLER SAHARA, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 158 (DTC INDEX)MODULE, STEERING CONTROL (SCM)
2011 Jeep Wrangler Sahara, Automatic
Module, Steering Control (SCM)
2011 Jeep Wrangler Sahara, AutomaticSECTION Module, Steering Control (SCM)
WARNING: This page is about a different car, the 2011 Dodge Journey. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| B1425-2A | REMOTE RADIO SWITCH INPUT - STUCK |
| B1504-2A | LEFT STEERING WHEEL CONTROL SWITCH - STUCK |
| B2306-2A | FRONT WASHER SWITCH - STUCK |
| B232E-00 | REAR WASHER SWITCH STUCK |
| B2332-2A | HORN SWITCH - STUCK |
| B23A1-2A | FLASH TO PASS/OPTICAL HORN SWITCH - STUCK |
| C1219-00 | STEERING ANGLE SENSOR ERRATIC PERFORMANCE |
| C121A-00 | STEERING ANGLE SENSOR NOT INITIALIZED |
| C123F-00 | STEERING ANGLE SENSOR COMPARATIVE PERFORMANCE |
| C1240-76 | STEERING ANGLE SENSOR ANGLE OVERTRAVEL PERFORMANCE - WRONG MOUNTING POSITION |
| C1241-00 | STEERING ANGLE SENSOR VELOCITY PERFORMANCE |
| C2129-16 | BATTERY VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C2129-17 | BATTERY VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C212A-16 | SYSTEM VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C212A-17 | SYSTEM VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C2205-00 | STEERING ANGLE SENSOR INTERNAL |
| P0579-00 | SPEED CONTROL SWITCH 1 PERFORMANCE |
| P0580-00 | SPEED CONTROL SWITCH 1 CIRCUIT LOW |
| P0581-00 | SPEED CONTROL SWITCH 1 CIRCUIT HIGH |
| P0585-00 | SPEED CONTROL SWITCH 1/2 CORRELATION |
| P0591-00 | SPEED CONTROL SWITCH 2 PERFORMANCE |
| P0592-00 | SPEED CONTROL SWITCH 2 CIRCUIT LOW |
| P0593-00 | SPEED CONTROL SWITCH 2 CIRCUIT HIGH |
| P1593-2A | SPEED CONTROL SWITCH 1/2 STUCK |
| U0002-00 | CAN C BUS OFF PERFORMANCE |
| U0100-00 | LOST COMMUNICATION WITH PCM |
| U0146-00 | LOST COMMUNICATION WITH CENTRAL GATEWAY |
| U0155-00 | LOST COMMUNICATION WITH CLUSTER/CCN |
| U1008-00 | LIN 1 BUS |
| U1009-00 | LIN 2 BUS |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.