Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2011LIBERTY LIMITED, RWDREPAIR AND DIAGNOSISGENERAL INFORMATIONDTC INDEXMODULE, MEMORY SEAT (MSMD)
2011 Jeep Liberty Limited, RWD
MODULE, Memory Seat (MSMD)
2011 Jeep Liberty Limited, RWDSECTION MODULE, Memory Seat (MSMD)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| B1D5E-13 | POWER SEAT SWITCH-CIRCUIT OPEN |
| B1D62-2A | POWER SEAT SWITCH STUCK-STUCK |
| B1D6B-11 | SEAT HORIZONTAL POSITION SENSOR-CIRCUIT SHORT TO GROUND |
| B1D6B-12 | SEAT HORIZONTAL POSITION SENSOR-CIRCUIT SHORT TO BATTERY |
| B1D6F-11 | SEAT FRONT VERTICAL POSITION SENSOR-CIRCUIT SHORT TO GROUND |
| B1D6F-12 | SEAT FRONT VERTICAL POSITION SENSOR-CIRCUIT SHORT TO BATTERY |
| B1D73-11 | SEAT REAR VERTICAL POSITION SENSOR-CIRCUIT SHORT TO GROUND |
| B1D73-12 | SEAT REAR VERTICAL POSITION SENSOR-CIRCUIT SHORT TO BATTERY |
| B1D77-11 | SEAT RECLINER POSITION SENSOR-CIRCUIT SHORT TO GROUND |
| B1D77-12 | SEAT RECLINER POSITION SENSOR-CIRCUIT SHORT TO BATTERY |
| B1D7B-00 | SEAT HORIZONTAL MOTOR CONTROL CIRCUIT PERFORMANCE |
| B1D7F-00 | SEAT FRONT VERTICAL MOTOR CONTROL CIRCUIT PERFORMANCE |
| B1D83-00 | SEAT REAR VERTICAL MOTOR CONTROL CIRCUIT PERFORMANCE |
| B1D87-00 | SEAT BACKREST MOTOR CONTROL CIRCUIT PERFORMANCE |
| B1D9B-54 | SEAT HORIZONTAL FRONT STOP NOT LEARNED-MISSING CALIBRATION |
| B210A-84 | SYSTEM VOLTAGE LOW-SIGNAL BELOW ALLOWABLE RANGE |
| B210B-85 | SYSTEM VOLTAGE HIGH-SIGNAL ABOVE ALLOWABLE RANGE |
| B210D-21 | BATTERY VOLTAGE LOW-SIGNAL AMPLITUDE < MINIMUM |
| B210E-22 | BATTERY VOLTAGE HIGH-SIGNAL AMPLITUDE > MAXIMUM |
| B221C-42 | (MSM) MEMORY SEAT MODULE INTERNAL-GENERAL MEMORY FAILURE |
| U0011-00 | CAN INTERIOR BUS OFF PERFORMANCE |
| U0013-00 | CAN INTERIOR BUS (+) CIRCUIT LOW |
| U0014-00 | CAN INTERIOR BUS (+) CIRCUIT HIGH |
| U0016-00 | CAN INTERIOR BUS (-) CIRCUIT LOW |
| U0017-00 | CAN INTERIOR BUS (-) CIRCUIT HIGH |
| U0141-00 | LOST COMMUNICATION WITH IPM (FCM/TIPM) |
| U0155-00 | LOST COMMUNICATION WITH CLUSTER/CCN |
| U0203-00 | LOST COMMUNICATION WITH LEFT FRONT DOOR MODULE |
| U0204-00 | LOST COMMUNICATION WITH RIGHT FRONT DOOR MODULE |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.