SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2011COMPASS LIMITED, AWD, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTINFOTAINMENTAUDIO (RADIO) - ELECTRICAL DIAGNOSTICSDTC TROUBLESHOOTINGB143D-MICROPHONE 2 CIRCUIT PERFORMANCEDIAGNOSTIC TEST
2011 Jeep Compass Limited, AWD, Standard

Diagnostic Test

2011 Jeep Compass Limited, AWD, StandardSECTION Diagnostic Test
  1. CHECK FOR ACTIVE DTC 
    1. Turn the ignition on.
    2. With the scan tool, read the active DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  2.

      No 

      • Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and correct pin tension.
  2. INSIDE REARVIEW MIRROR 
    Fig 1: Inside Rearview Mirror Harness Connector End View
    GC0103625Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Disconnect the Inside Rearview Mirror C2 harness connector.
    3. Turn the ignition on.
    4. With the scan tool, read the DTCs.

      Does the scan tool display this DTC as active?

      Yes 

      • Go To  3.

      No 

      • Replace the Inside Rearview Mirror in accordance with the Service Information.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.
  3. (X722) MICROPHONE 2 IN (+) CIRCUIT SHORTED TO GROUND 
    Fig 2: Checking Microphone 2 IN (+) Circuit For Short To Ground
    GC0103626Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Disconnect the Radio C2 harness connector.
    3. Measure the resistance between ground and the (X722) Microphone 2 IN (+) circuit.

      Is the resistance below 10K ohms?

      Yes 

      • Repair the (X722) Microphone 2 IN (+) circuit for a short to ground.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.

      No 

      • Go To  4.
  4. (X722) MICROPHONE 2 IN (+) CIRCUIT SHORTED TO VOLTAGE 
    Fig 3: Checking Microphone 2 IN (+) Circuit For Short To Voltage
    GC0103627Courtesy of CHRYSLER LLC
    1. Turn the ignition on.
    2. Measure the voltage between the (X722) Microphone 2 IN (+) circuit and ground.

      Is the voltage above 1.0 volt?

      Yes 

      • Repair the short to voltage in the (X722) Microphone 2 IN (+) circuit.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.

      No 

      • Go To  5.
  5. (X722) MICROPHONE 2 IN (+) CIRCUIT OPEN 
    Fig 4: Checking Microphone 2 IN (+) Circuit For Open
    GC0103628Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Measure the resistance of the (X722) Microphone 2 IN (+) circuit between the Radio C2 connector and the Inside Rearview Mirror connector.

      Is the resistance below 5.0 ohms?

      Yes 

      • Replace the Radio in accordance with the Service Information.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.

      No 

      • Repair the (X722) Microphone 2 IN (+) circuit for an open.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.