SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2011COMPASS LIMITED, AWD, AUTOMATIC CVT, CVT2REPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTENTERTAINMENT SYSTEMSAUDIO (RADIO) - ELECTRICAL DIAGNOSTICSDTC TROUBLESHOOTINGB1407-FRONT RIGHT AUDIO SPEAKER OUTPUT CIRCUIT OPENDIAGNOSTIC TEST
2011 Jeep Compass Limited, AWD, Automatic CVT, CVT2

Diagnostic Test

2011 Jeep Compass Limited, AWD, Automatic CVT, CVT2SECTION Diagnostic Test
  1. CHECK FOR AN INTERMITTENT CONDITION 
    1. Turn the ignition on and open one of the front doors.
      NOTE:

      A front door must remain open whenever checking or erasing Radio DTCs.

    2. Using the scan tool, record and erase the Radio DTCs.
    3. Turn the Radio on.
    4. Adjust the speakers to the front and center.
    5. Using the scan tool, read the active Radio DTCs.

      Does the scan tool read: B1407-FRONT RIGHT AUDIO SPEAKER OUTPUT CIRCUIT OPEN?

      Yes 

      • Go To  2.

      No 

      • Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and correct pin tension.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.
  2. CHECK THE RIGHT FRONT SPEAKER 
    Fig 1: Checking Right Front Speaker
    GC0138649Courtesy of CHRYSLER LLC
    1. Turn the ignition off.
    2. Disconnect the Right Front Speaker.
    3. Measure the resistance of the speaker between the two terminals.
      NOTE:

      The graphic shows the connector for reference only. Measure between the speaker terminals.

      Is the resistance above 5.0 Ohms?

      Yes 

      • Replace the Right Front Speaker in accordance with the Service Information.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.

      No 

      • Go To  3.
  3. CHECK THE (X202) RIGHT FRONT SPEAKER (+) CIRCUIT FOR AN OPEN 
    Fig 2: Checking Right Front Speaker (+) Circuit For An Open
    GC0138650Courtesy of CHRYSLER LLC
    1. Disconnect the Radio C2 harness connector.
    2. Measure the resistance of the (X202) Right Front Speaker (+) circuit between the Radio C2 connector, and the Right Front Speaker harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  4.

      No 

      • Repair an open in the (X202) Right Front Speaker (+) circuit.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.
  4. CHECK THE (X292) RIGHT FRONT SPEAKER (-) CIRCUIT FOR AN OPEN 
    Fig 3: Checking Right Front Speaker (-) Circuit For An Open
    GC0138651Courtesy of CHRYSLER LLC
    1. Measure the resistance of the (X292) Right Front Speaker (-) circuit between the Radio C2 connector, and the Right Front Speaker harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Replace the Radio in accordance with the Service Information.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.

      No 

      • Repair an open in the (X292) Right Front Speaker (-) circuit.
      • Refer to Standard Procedure and perform the BODY VERIFICATION TEST.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.